Tom’s Miata: Frankenstein Fun

Tom’s story began with his Mini Cooper in the fall of 2018. Then in high school, he cobbled together parts from forums and Craigslist Marketplace postings and ended up pushing a little 230 horsepower and 270 lb-ft from the 1.6-liter. It carried him through his track day foray, but the more he drove it, the more it faltered. He couldn’t keep up with the costs, the fuel, and the track day entries.

His friends suggested a simpler car to try and earn his driving spurs with. By parting out the Mini, he could put together the few thousand he needed to pick up an NC Miata with nearly 200,000 miles on the clock. The NC had lived an unloved orphan’s life; moving through seven households before ending up in Tom’s driveway. Somehow, it was still stock when he bought it. This basic package promised regular attendance at local lapping events, even with his college schedule limiting his time and his finances.

Tom didn’t have the means or the interest in going ga-ga with the mod list. The basic package of Feal 441+ Road Race coilovers, RX-8 sway bars, and Cobra Suzuka buckets did him just fine as he was making his way from novice to intermediate. The objective was to get good enough to feel comfortable at the limit and fix what broke.

Fortunately, little did. The only issue in that busy twelve months was the OEM radiator bursting. In the first year of racing, Tom and a few trusted friends logged over thirty DEs on the dependable little Miata. It actually helped him earn a few bucks, too, after reading Engine Management: Advanced Tuning by Greg Banish, he picked up enough to start tuning the factory ECU and starting a side hustle. That money went to his track fees, and it seemed like he’d found a self-sustaining system for himself. All was well with the world until it wasn’t.

After the engine blew, he borrowed his friend’s daily to finish out the final three weeks of his final semester at school, then bought the remainder of a friend’s parted-out NC track car, which fortunately still had its motor. It wasn’t an ordinary two-liter. His friend had swapped in a 2.5 from a Ford Fusion, a budget upgrade with minor architectural differences to the 2.0 it replaced. Swapping it into his car took less than three days.

Unfortunately, the stock 2.5 fell flat on its face at 5,500. With a set of OEM Mazdaspeed 3 valve springs and a set of Xero Limit “Boost” camshafts, Tom was able to raise the 2.5’s rev limit without any thinning of the functional powerband. The 170 lb-ft on tap starts around 3,000 and carries through 5,000, and the power keeps building to the 7,100-rpm redline, where it makes 197 at the wheels.

A comparison of the 2.5 on E70 (red) versus the 2.0 on 91 (blue).

“The objective has been to see how fast I can go without cutting corners or spending much money,” he elaborated. This is Tom’s main reason to try and use as many OEM components as possible. To avoid dealing with the factory rear hubs shearing, he upgraded to a set of hubs from its stouter older brother, the RX-8.

Though it required a bit of custom work to make it fit, the in-the-family RX-8 differential helped tremendously. Better, more progressive breakaway and improved acceleration from a 4.1 final drive originally suited to a torque-free rotary. After this upgrade, the car no longer lost speed going uphill between Turns 8 and 9 at Thunderhill East.

Because the RX-8 differential is taller, in order to sit in the same spot, Tom had to move the alignment area for the studs to sit in the same spot, which meant losing the alignment dowels. Without these, the powerplant frame eventually started sagging after a few months of hard driving. Eventually, this led to the powerplant frame contacting the midpipe under heavy braking and curb hopping. His attempt at notching the powerplant frame was one piece of trial-and-error that didn’t go his way, but he plans to put a set of custom locator plates to avoid this problem permanently.

Currently, he’s fighting the smaller issues like the one above which make the car hard to drive as regularly as he’d like. “Mostly just little gremlins from the engine swap,” he added. Other than that, it's the wallow from the original bushings which make the Miata a bit unpredictable at times. That’ll be relatively straightforward though time consuming.

If his first year out of school is as lucrative as he hopes, he might assemble a new motor to make the MX-5 a real S2000 rival with the following parts: a Fusion’s 2.5-liter Duratec block and pistons, and a Mustang’s 2.3-liter Ecoboost connecting rods and crankshaft, 12:1 compression and an 8,200 rpm redline, he’s hoping for 270 horsepower at the wheels. “It’s going to take a lot of development on my end, but I’ve got a small group guiding me. I’m in good hands.”

Along with the added speed comes a need for better deceleration, so in addition to a set of four-piston Wilwood calipers and RX-8 Sport rotors (which are only $30 per corner), he’s gone and picked another part within the Mazda lineup that takes a little innovation and forum-digging to swap. The RX-8’s ABS system is less prone to engage ice mode. Though this will be another trek down an unpaved path, he’s been given the schematics from others and feels confident the swap will be successful.

“It’s been fun to Frankenstein because I like doing things that not many have done, but I’m more interested in retaining a lot of OEM equipment since I don’t think it will have many issues in the long run. Hopefully, these parts will make it easier to go out and drive more miles. I still need seat time more than anything. Seat time, saving money, and keeping it reasonably streetable have been my objectives. I think I’ve achieved most of them."

Now, I’m considering making it more of a race car since I’ve got a daily now. But until I can afford a truck, there’s no point in making it a total pain to drive. The added torque is definitely enjoyable in the canyons, where I can keep it in third most of the time.”

How many Miata owners can say that?

Cory’s C6 Grand Sport: Safe Not Sorry

He’d spent several years finding his feet in a Mustang, but after his friend was kind enough to let him try their Corvette Z06 at a track day, Cory Smetzler knew he had reached a junction, and although it would cost more, the prudent thing to do was to take a left turn.

The C6’s shape stimulated his imagination, and the performance was already so much more than what he’d been accustomed to; the Z06 in near-stock trim could already outperform his highly-modded Mustang. It was clear that it was time for a major change.

But Cory is a practical person, and making an expensive shift could not be justified by the C6’s soft, curving lines and wide arches alone. Pretty as it was, it was the performance package which convinced him to shell out some more coin, since its improved weight distribution, roomier wheel wells, and dead-reliable engine package promised much more fun and fewer headaches.

A set of American Racing headers bumps output to 470 horsepower and 470 lb-ft of torque at the wheels.

And pragmatism kept him from buying the same model, too. Instead of taking a chance with the Z06’s LS7 motor and its propensity to swallow a valve, he instead opted for the mid-tier Grand Sport, which loses the special motor and the aluminum frame. In their place, the Grand Sport comes with a more pedestrian LS3 and a steel frame, but for the price of less power and more weight, Cory purchased peace of mind.

Though the LS3 isn’t quite the motorsports-grade product the LS7 is, the improvements already made to this particular motor helped Cory forget about lost potential. The previous owner had installed a Dewitts radiator, a FAST 102 mm intake, a Nick Williams throttle body, as well as Doug Rippie Motorsports differential and transmission coolers.

The powerplant ran smoothly in the sweltering summer heat, though the engine lacked that zing and top-end that the other Corvette had, the mid-range torque of the mildly tuned LS3 was plenty exciting.

Mated to a TR6060 six-speed transaxle, the torquey LS3 and its 400-odd horsepower could get the car to GT3RS-speeds surprisingly quickly, so Cory wasted no time giving his new track car the stopping power and safety modifications that it warranted. He doled out the big bucks for an AP Racing Essex front brakes with 372mm rotors and inch-thick pads which guaranteed stopping power, consistency, and long pad life. No sense in taking shortcuts when stopping a heavy, powerful car.

Its accessible mid-range torque is exploitable on shorter courses and still strong enough to reach similar top speeds on faster ones. Surprisingly, the wonderful spread with the right combination of wheel size and final drive make it effortless to keep the engine humming along without the need for many shifts. This is a large part of what makes it so effective at tight tracks.

A 3,300-pound Corvette shows its shortcomings on tighter tracks. The poor motion ratio of the rear leaf springs pushed Cory to double the rear spring rate, which allows for the car to break away more progressively, and the resulting confidence from this predictable sliding helps Cory drive the car with more slip angle than he has with any other car.

The willingness to push a tail-happy car hard in the butt-clenching corners takes more than just progressive breakaway. Cory added a Nine Lives Racing single-element rear wing, mounts, endplates, front tunnels, and a homemade birch splitter added the stability he needed to trust the Corvette in fourth-gear sections at faster tracks like Sonoma.

The current setup isn’t perfect, but it’s nearly there. There’s the matter of weight to deal with, and he’d still like the rear to be better settled, but it is reliable and relatively kind to its tires, and so he’s been able to put in plenty of hassle-free track miles without going through too much rubber. Low maintenance and lots of seat time has been his credo since the start, and he’s hired Joe McGuigan to help put his philosophy to good use. With a little coaching, he’s been putting down impressive times after just a couple visits to Sonoma.

Since his recent move from the Pacific Northwest to Southern Oregon, Cory’s been able to enjoy the temperate weather and make it to track days with more energy and regularity. Seeing as how he’s been able to set impressive laps at circuits that are new to him, it’s certain he’ll be a force to be reckoned with in our Challenge series very soon. We’re happy to have him.

Alex’s FL5 Type R: Best of Both Worlds

For Alex Peysakhovich, living in NYC had its perks, but easy access to track days was not one of them. When he relocated to Los Altos and found himself with a backyard and a garage, he decided it might be time to purchase that car he’d always wanted and take advantage of California’s temperate weather and multiple tracks within a few hours’ driving distance.

His heart was always with Honda, but the then-current FK8 Type R was too boy-racer for his liking. “I really loved the car, but thought about some things you have to do with your only car, like go to a business meeting or drive in a funeral procession, and I couldn’t really imagine doing those in an FK8.”

So instead he began tracking with an ND Miata. Heavy modification made it a capable cornering machine, but its impracticality became a constant pain; it needed a trailer for long drives and couldn’t be used to take his dog and his girlfriend on weekend trips. He thought about getting an electric daily that he wouldn't track or modify, but that idea didn't last long. “What’s the point of buying a car you’re never going to take to the race track?” he asked himself.

Enter the FL5 Civic Type R, which debuted after a couple years of tracking the Mazda. The new Civic traded its predecessor’s divisive looks for more subdued styling, so Alex had to check it out for himself.

“I used to think Type Rs were a little overhyped, but after seeing it in person, I recognized why the car has a cult following,” he said.

He appreciated the way Honda’s engineers made this fifty-grand Civic feel unmistakably upmarket. But more than presence or build quality, it had real-world usability going for it. On longer trips, the comfortable seats were a welcome upgrade from his Miata’s race buckets. The interior space, the fit and finish, and the performance made the FL5 a great candidate for a daily driver-come-sleeper, and once the premiums started to shrink, Alex pulled the trigger and brought one home.

Before his first track outing, he made a few adjustments. He’d learned enough to know that a ~3,200 pound front-driver would wreck its Pilot Sports fairly fast, so he ditched those for a set of 265-section Bridgestone Potenza RE-71RS tires wrapped around Apex VS5-RS wheels. Along with a set of eccentric lower ball joints to increase negative camber at the front axle, he replaced the stock pads with a set of Ferodo DS3.12s to help clamp the factory two-piece rotors.

He broke it in over 600 miles then took it to Thunderhill West for its shakedown, where he was pleasantly surprised. The steering was quick, despite a dead spot at twelve o’clock, and the gearbox was, well, Honda. If the interfaces were lacking in any way, it was the position of the throttle — as he put it, “in another zip code.” Thankfully, the auto-blip function facilitated heel-toe shifts despite the awkward pedal placement.

Being a front-drive car, he had expectations for how it might handle on a damp morning. Those were dashed on his first fast lap after mounting the dorito at Turn 3, when it hung the rear out in a big way.

“As far as a car that can pack a weekend of camping gear and do great times around Laguna, it’s a hard car to beat.”

The FL5’s mechanical LSD and brake-based stability control system do a commendable job getting the middleweight to rotate. What was less than impressive were the thermal problems which have been associated with the turbocharged Type Rs. Though not catastrophic, the heat causes the motor to pull timing by the end of a long session, but never puts it into limp mode. “I think there’s only so much you can expect from a turbocharged two-liter making over 300 horsepower,” Alex added.

Fortunately, these issues are not new to the Type R lineup and the FL5 was designed to make them easier to address than its predecessor ever allowed. The ducting routes have been established from the factory, along with a functional hood vent. Honda laid the groundwork, but more needs to be done for hot summer days. “It isn’t imperative, but it could use a bigger radiator and an oil cooler. I’ve got those sitting in my garage in anticipation for the summer.”

“The designers cared about the experience of the car; they wanted it to feel special, even when parked.” Alex added. Credit: Tokumeigakarinoaoshima CCA-SA 4.0.

Beyond that, any remaining mods are far from necessary. The FL5 is well-balanced out of the box and does not need much more power. “The engine is certainly strong. If it could use something to make it feel a little sportier, it would be an exhaust — it’s too quiet.”

That subdued exhaust note is part of what makes the car so versatile, and its wide repertoire comes at a premium. Besides requiring pricier fuel, the turbocharged front-driver is hard on its front brakes and tires, and it goes through consumables far faster than a lighter, better balanced car like a Miata.

There’s no denying the running costs are too high to track a Type R regularly — multiple track days per month will continue to be the Miata’s job — but the Civic will be doing daily driving, mountains, longer trips, and rear its head at Laguna and Thunderhill East a few times a year.

Four years ago, Alex thought fifty thousand for a Civic was steep, but he’s changed his tune as of late. “I know that sort of money for a Civic sounds crazy, but you really need to try it. It’s tough to think of something similarly priced that handles so many different tasks as well as the Type R. If I could only have one car, this would be it.”

Gordon’s M2: Iteration Cycle

After beginning HPDE during an Apple track day at Thunderhill East, Gordon Mak found a new outlet for his workplace frustrations and his analytical habits.

The Golf R he got his start with proved to be impractical, and practicality being a criteria he’s used to pick his collection of track cars, it didn’t last too long. The Golf’s nannies intervened too much to get closely acquainted with, as the instructor sitting alongside Gordon mentioned several times.

That instructor also encouraged Gordon to look in the right direction, squeeze the throttle with caution, and soften his steering inputs as much as possible. That coach did Gordon an enormous favor that day by instilling good habits in a firm yet friendly fashion. On his drive home, he had a moment to ponder the afternoon’s teachings. Gordon recognized that his new hobby would require two things: a communicative car and the right skillset needed to exploit its full potential.

By the next spring, Gordon was presented with a chance to buy a first-gen BRZ for invoice. The rawness and urgency of a lightweight, balanced car had him hooked, and the first big spin at The Andretti Hairpin had him shook. “Oversteer was a new concept to me,” he said.

Rather than remain intimidated, he tried to suss out his shortcomings then and there. In analyzing his onboard footage following that track day, Gordon could clearly see how ill-equipped he was to deal with the situation. “I just froze; my hands didn’t move at all,” he admitted. 

While some told him it wasn’t the prudent thing to do at that stage, Gordon took a leap and bought an even tail-happier car in the middle of the pandemic. The price was right, and the on-tap torque from a twin-scroll turbo motor and short wheelbase made the GR Supra a lively, exhilarating car with which he could develop his car control skills.

From then on, he committed to the invaluable skid experience of Drift SF, where he could hold long slides, connect corners, and spin without any consequence. “It was sanctioned parking lot hoonery — low credit score activity — that helped me make my first big steps as a driver. By the second event, it all clicked for me,” he said.

“I have to thank Joe McGuigan for teaching me how to slide the car with confidence. Once you move past the pit-in-stomach feeling of losing traction and the belief that you’ll be unable to respond, you can get a lot done. Without all the drift practice, I wouldn’t have felt confident enough to keep pushing,” he explained. 

As fun as it was, the Supra lacked the directness of the GT86. When the dealership he bought the Supra from offered to buy it back for the same price he paid a year prior, he didn’t hesitate. Without waiting, he replaced it with a GR86 and ran eighteen successful events over the next eighteen months.  

The unfiltered driving experience he’d missed so much during his Supra ownership had returned, but not without some adjustment. “After I switched to the GR86, I found myself - for a few events, initially - making unnecessary steering corrections because I had built up so much muscle memory from the Supra always going sideways. It took me a surprisingly long time to get over it, he explained. But even after altering his technique, there was one potential issue he couldn’t get his mind off of. “The ever-present possibility of losing an engine made it difficult to enjoy the car.”

Finding a suitable replacement was simpler at this stage, since Gordon had determined precisely what he was looking for in a track car. He wanted something dependable enough to run full sessions at Thunderhill in the middle of July, something that had adequate performance out of the box, and something which would carry a spare set of wheels and a couple suitcases if needed. Essentially, it had to be mostly turnkey and, if necessary, require only minimal modification. 

Two drivers helped motivate his decision to buy a new M2. First, Randy Pobst’s hot laps in a particular stock car at Laguna, when compared to the PBs set by amateurs in heavily-modded examples of the same model, helped Gordon recognize how big a factor driving skill truly was.

Jackie Ding, the other pro responsible for his decision, had demonstrated what the new M2 was capable of in mostly stock form. While he was worried he might have another Supra experience ahead of him, he took the gamble and sold his GR86 for a brand new M2 in Zandvoort Blue.

Since he recognized the value of seat time, he had less interest in modifying the car heavily than some of his peers. “I’m less concerned with lap times now,” he began. “I’d rather have a few modifications to help me feel calm and confident in the car, but I don’t really have a mod-itch to scratch. I’m more interested in the activities which help me improve as a driver, both on and off the track. If I have an itch to scratch, it’s an itch for self-improvement.”

That said, there’s still some room to make a heavyset grand tourer more at-home on the track, and if he can make a modification or two that will save him in consumable costs, why not? With Millway front camber plates, CSG CP pads, SRF brake fluid, and a square set of Apex VS5-RS wheels measuring 19x10”, he had all he needed to run track days comfortably while keeping his tire bill reasonable. 

The two issues with the car, besides its unignorable mass, are that it’s slightly under-tired and the ZF8 gearbox leaves a little to be desired. “I went a little too conservative with my wheel choice, possibly. It’s even tail-happier than before; I can drift the car in fourth and fifth gear now!” he laughed. 

Some of that is due to the ZF8’s short gearing and the way it shifts somewhat harshly. “It’s easy to spin and lock the wheels on even a slightly damp track.” It’s a lairy sort of car that’s constantly on the verge of oversteer, but at least slide correction is no longer a foreign concept — it’s now something he does without thinking.

Gordon still has some plans for the M2 in the future, but as it’s been happy to run coolly on the hottest days, transport him to and from the track in comfort, and make his track days a little less stressful that the rest’s, he’s content with it as it currently sits. His heart still pulls him towards something lighter and more visceral, but the M2 is about as good a streetable track toy gets. 

And that practical package makes it easier to pursue his main aim, which is to interact with the track community, get enough seat time, and hone his craft as a driver. The fact that the M2 is well insulated helps him hear his coach’s feedback from the driver seat is an added bonus. 

“If you really listen to your instructor, you will improve. I try to remain open minded, test the suggestions coaches and friends give me, and analyze the results. If I can get into an iteration cycle with whomever I’m working with, I’m confident I can find an effective solution to any problem pretty quickly,” he added.

Gordon’s story is one which demonstrates the value of analysis, and, necessarily, the importance of the human element. Rather than descending down the rabbit hole of buying parts to find speed (and justify the costs), he took a different path. He’s searched for the answer to his particular problems and found a repeatable process to keep him active, happy, and stimulated. That’s not something that can be found trawling the forums for an answer.

Joe’s M3: Proving His Potential

Photo credit: CaliPhoto

When building a track car, it’s almost always easier to take the paved path. Picking a platform that has been thoroughly developed, with available parts for every possible problem and associated forums filled with information help get the driver to the track without much wrenching.

Not that ease was the main reason Joe McGuigan decided to add an eighth car to his collection — he did that because his friends urged him to try the car he’d avoided for a while. They were tired of watching him struggle with his trailblazing passion projects. They said he’d be able to save himself time if he just joined the tribe and bought an E46 M3.

When Spencer Kimball decided to sell the E46 he’d built for his father, whose injuries prevented him from enjoying it, half of the greater NorCal track community flooded his inbox. Spencer had already proven he knew how to put a seriously quick M3 together, and this example checked just about every box a track car needs to. Plus, the price was impossible to argue with. It would make some track rat a very happy owner soon enough, but an iconoclast like Joe? Not likely.

He was well aware of the M3’s potential, but he never found it interesting enough to build one himself. He preferred the challenge of developing a less-loved car, and always found the E46 M3’s competence a bit boring. Too easy to drive quickly, too easy to build. Not enough of a challenge for a man trying to prove a point.

However, the long list of primo parts and the low, low price were too tough to ignore. Joe had to accept the “boring” car for the simple fact that he would no longer be able to handicap himself with a sub-par chassis. “I could show people how fast I really am,” he added. Rather than prove a point as a builder, he could prove himself as a driver.

He mulled it over for a few days before pulling the trigger. Picking it up on the way home was the easy part. Driving it back to his crowded driveway, it dawned on him how big a task he’d set for himself: “Now I’ve gotta put my money where my mouth is and build a really fast car,” he said.

Fortunately, the car was already well on its way towards perfection. Spencer had big plans for the build and sank a good amount of money into making it fast, reliable, and fun to drive. The short list includes:

• Shaftworks USA coilovers with 500/750-lb springs

• Custom Drexler-style 1.5-way differential

• 4.10 gears

• SPL arms

• Supersprint V1 header

• CSL intake

• HTE tune

• E90 GTS rear wing

• Bimmerworld diffuser

• Bimmerworld 3” exhaust

• PFC ZR45 BBK

• APEX Wheels 18x10" ET25 Forged VS-5RS

Those and a few minor mods were all Joe needed to set some competitive times. The first track day was a few days after pickup, so he only had time for an alignment and a fluid flush. Nevertheless, its first outing in his hands, a two-day event at Buttonwillow, was a success.

He found it fast and forgiving, with a linear power delivery and direct steering. Those qualities, plus a hint too much understeer, helped Joe get on top of the car in a session. By the end of the first day, he lapped Buttonwillow 13CW in 1:56.3 — on an old set of Toyo RRs, no less. The predictive timer showed an optimal lap a half-second faster which, funnily enough, is one tenth shy of his best-ever time at 13CW in his well-developed IS-F.

He’s already sussed out its shortcomings and drummed up a short list of solutions which he plans to implement soon. Being able to knock out problems quickly with the support of a vast market is one of the reasons going with a well-loved platform makes sense. “I plan to move pretty quickly with this build. Who knows? I might sell it next year,” he laughed.

The brakes are capable, but the pads might need to be changed as the initial bite wasn’t strong enough to give him much confidence. The spring rates are too low; the owner before Spencer had specced them for autocross. It’ll receive MCS two-ways, a TC Designs cage, reinforced swaybar brackets, and full Zebulon/Buildjournal aero in the next couple months.

But the bones are good, as they say, and it’s already fast enough to aim for some of the times set by friends and colleagues in the E46 scene. While he hasn’t given up on his IS-F, he’ll fixate on beating the established BMW benchmarks for the time being.

Andrew from Buildjournal has taken his E46 M3 just about as far as anyone on the West Coast has, and his car can turn a lap around 13CW in the 1:49s. “I’m sure its capable of something in the low 1:50s with weight reduction, a better setup, and full aero,” Joe declared. There’s no reason to doubt it.

The potential is obvious, the build is nearly finished, his connections are eager to help him, and all he’s had to suffer is a little boredom. The E46 might not pull at the heartstrings like some passion projects, but he can’t deny the potential that the project holds — and the fun he’s already had with it — has caused him to change his tune.

Richard’s MR2 Turbo: Not Too Pretty To Pirouette

It began all the way back in grade school with Gran Turismo. A few years later, Richard Tran graduated from video games and started moving through the worlds of hard-parking BMWs and drag racing until his expanding network brought a few road racers into his life.

When they invited him to a track day with Speed SF in 2019, he accepted — but not before considering the consequences. Richard was opposed to taking big risks; he’d seriously hurt himself in a car crash a few years before, and he certainly didn’t want to damage his then-new M3, but they persisted — they told him he’d leave the the track feeling something extraordinary.

The feelings of euphoria following that first session helped him forget about the potential costs of thrill seeking. In fact, he’d been bitten badly enough to sign up then and there for another twelve track days. Quickly, he put the dependable M3 on the back burner; he had a cheaper, lighter, more maneuverable mid-engined car he believed would take more to master.

To the trained eye, his 1991 Toyota MR2 Turbo (SW20) didn’t look like the ideal track toy candidate. Actually, it looked more like a museum piece. Three-stage paint, fresh interior panels, and completely new suspension components were all parts of a three-year restoration that culminated in a show-grade vehicle. Richard was so proud of it, he displayed it at SEMA.

Work Meisters and the OEM kouki aero was all that was needed to make the SW20 pop — it truly is a svelte, sexy car.

Despite its immaculate condition, he felt it wasn’t too good to be used in the way he’d (ab)used his M3. In fact, Richard felt that he’d be missing out on something vital if he didn’t track it. There was a directness and a demanding quality about it that made him feel giddy at 5/10ths.

The second outing proved he had his head screwed on straight, but didn’t quite have the quick hands needed to manage the MR2. The factory components just wouldn’t cut it, especially on all-seasons, so he replaced the rotors with slotted Stoptechs and slapped on a set of EBC Yellows. Along with those, he installed a set of Tein Super Street coilovers, a pair of GReddy side skirts, and a 1998-spec spoiler with lifted risers for a little flash.

The basic package was fun, but far from friendly. “I made the mistake of trying to drive it like the M3,” he began, “and that just wouldn’t work. I learned pretty quickly that I couldn’t throw it around or brake as late as I could in the BMW.”

The odd agricultural excursion didn’t dampen his enthusiasm for his demanding new car.

After many red flags and several stern conversations with the track workers, Richard learned he had to soften his inputs a little and improve the chassis a lot. The second-generation MR2 is known as a nervous car prone to rotate without much provocation, but it can be tamed with some suspension work, a little maintenance throttle, and the right sort of staggered tire setup.

Giving precedence to the rear axle began by fitting the rear wheels with 245/40R17 Federal RS-RR Pros — somewhat wider than the 215/40R17 fronts. Then, Richard turned to Elite Performance’s Melody Cannizzaro to soften the sensitive midship’s edges. A little more front camber relative to the rear helped settle the rear end while cornering, and more toe-in at the rear kept it planted under braking and acceleration. Then, as advised by his friends, Richard tried stiffening the front to minimize the nose dive under heavy braking, which could encourage the lightened rear to spin.

Minimizing some of that see-sawing gave him much more confidence in the car, and the resulting improvements in cornering speeds helped Richard notice a few more of its shortcomings.

It wasn’t the tight, direct thing he thought a lightweight MR car would be, but, after all, it was nearing a half-million miles. Sunshine Auto overhauled the entire suspension, adding new control arms, bigger sway bars, inner and outer tie rods, additional chassis bracing, and a set of 808 Racespec coilovers from Bob Pham. “The new setup made the car feel like a go-kart. Actually, the first day back at the track with these mods, I went six seconds faster than I’d ever gone before,” he exclaimed.

Richard’s love for the Sailor Moon series gave this car its eponymous nickname.

“Those modifications transformed it from a decent daily driver to an uncomfortable track car, but I still trust it enough to drive it to the track — it hasn’t left me stranded once,” he said. Pretty impressive for a car that just passed the 500,000 miles on the odometer. Chalk a bit of that up to build quality from the late-eighties Japanese boom, some of that to Richard’s obsessive maintenance habits, and a little bit to the near-stock configuration of the power train.

Aside from a Mishimoto radiator an HKS SSQV BOV, and a Berk 3” exhaust, the original 3SGTE motor remains stock.

Aside from a splitter and a pair of canards, Richard doesn’t plan on adding much more. Actually, he’s confident enough to admit he’s the limiting factor at this stage. “My friends will get in and go six seconds faster than I can, so I know I need seat time more than anything. Well, I could use a set of Sparco Circuits because I’m getting thrown around on the stock seats, but that’s about it.

For me, it’s the perfect track car — dependable, fun, and constantly challenging. I don’t really care about making it the fastest car here. I’ve got a ways to go as a driver, anyways. I’m not here to be the best — I just want to have fun, and in that department, the MR2 always delivers.

My track friends’ words of encouragement and support have been a driving force behind my journey; pushing me to overcome obstacles and strive for greatness. I rolled my car once many years ago and I was in the hospital for months. I thought I wouldn’t walk again.

My wife did not want to see me in another accident ever again. Actually, she wanted me to retire, but she saw how happy I was attending track days with friends, so she now watches me track. I promised her I’ll never go completely flat-out ever again and I’m fine with that — as long as I get to see her smile.”

Special thanks to Elite Performance, The Driveway, and Sunshine Auto.

Joe’s AP1 S2000: Continuing Education

It wasn’t until Joe Drane moved out to California at the ripe age of 38 that he was able to try track driving for himself. Being a natural tinkerer and a bit of a hot rodder growing up, track driving had been a lifelong dream, but the opportunities for that sort of thing in rural Florida were few and far between.

After teaching him the ins and outs of network engineering, Joe started learning the cloud and found a few roles with startups in Texas. This created a focus on execution and continuous learning while also placing high value in data helped him put together a stellar resume in short time. This almost obsessive approach would later help Joe learn at a ridiculously rapid rate when learning the racing ropes.

The Land of Milk and Honey

After relocating to San Francisco to start a new role with Facebook, the assortment of beautiful sports cars lining the streets suggested he might be in the right place to learn to drive on track. He searched for ins on the pages of the local sanctioning bodies until he found an easier, more cost-effective way to dip his toe in the water.

Meanwhile, the need for a new outlet was getting harder to ignore. COVID weighed heavily on him, and while he loved his new job, it didn’t offer the distraction he needed mid-pandemic.

When he proposed running a few lapping days one weekend, his wife not only supported him in his decision, she helped him find an appropriate track car. Incidentally, the two had met at work after Joe spotted her leaving her S2000 in the parking lot. It only seemed right that such a car, the conversation starter, would help him start another love affair.

And so he picked out the cheapest first-gen S2000 he could find. This was several years ago, but even by the standards of the time, this car was affordable — and for good reason. “It was just a mess. It had no rear glass, the check engine light was on, the wiring was a rat’s nest, and the motor was ticking. I spent the winter restoring it, but I didn’t realize just how bad things were until I started working on it.”

Growing Pains

“I ran into some issues installing the aftermarket parts. The radiator wasn’t sitting low enough for the hood to close. I took it into the shop at BlackTrax to have it inspected, and there the mess continued to unfold. The radiator supports were bent, and I couldn’t purchase new ones anymore. I had to source the brackets from two fender cutouts from eBay.

Then we pulled the cylinder head and saw the valve retainers were cracked, there was a ton of carbon on the valves, and two of the cylinder walls were scarred. After ten track days, the transmission blew third gear. Oh man, what a nightmare it was.”

To mend the ailing engine and fortify it for track use, he replaced the block with rebuilt F22’s, then fitted a Radium catch can as well as Mishimoto’s radiator and oil cooler. Not eager to deal with another blown F-series, he wisely spent a few thousand more on a Link G4+ ECU to employ several failsafes and extract everything from the motor — mainly more mid-range torque and a peak of 227 horsepower at the wheels.The Link was then paired to an AiM MXG dash which to give him alerts and relay lap data.

Despite the early hurdles he had to cover, he remained willing and able to push on. The obsessive drive which fueled Joe’s career now had a second outlet; allowing him to research the engineering involved, pick parts, test them on track, and build a more supportive social network than the one which work provided him.

As it gave him a new lease on life, he didn’t hesitate to spend whatever was needed to turn this rough example of an S2000 into something exceptional. Within a few months, he’d added a long list of modifications to try and breathe some new life into this aging chassis.

After investing so much in the performance side of things, it made sense to apply an Inozetek wrap to help the car pop.

Among those additions were an APR splitter, a Voltex Type II wing, Rockstar Garage’s Feal two-way coilovers, and Stoptech C43 (F) and C42 big (R) brakes. Studying hours of onboard footage — namely Nate Hackman’s banzai laps — helped him understand just how much harder he could apply the brakes and how severely late he was getting to throttle.

In the interest of getting up to speed quickly, he skipped the cheap tires and went straight to a set of Yokohama Advan A052s, then wrapped them around a set of 18 x 9.5” Advan Gram Lights.

Though he’d already spent a small fortune on parts, never once did Joe agonize over expense during this introductory period. “I decided to pay for an education in racing since I feel it usually pays dividends,” he said. When his engine tuner Jei from BlackTrax offered to tag along to one HPDE at Thunderhill and teach Joe to study data, he jumped at the opportunity. “The telemetry revealed I was shifting a little too much, so we figured out the right shift points and instantly cut a couple seconds off my PB.”

The car was capable and reassuring enough for Joe to continue pushing, but asking more the car led to the standard Torsen differential failing. In its place, Joe put a Puddymod 1.5-way OSG and found the incremental improvement in power-down and stability motivating enough to invest in one other area that wasn’t quite up to snuff: dampers.

Joe knew the top-shelf option would make the car more quicker, more predictable, and less taxing to drive, so he splurged on a set of Blacktrax-built Penske 8300s. Even without much knob turning, the new dampers revitalized the car and helped Joe find the confidence to commit to the quick corners. “My favorite mod, without question. I dropped six seconds off my previous best the first time out on the Penskes. Worth every penny.”

Continuing Education

Learning to wrench and approach the track from a theoretical perspective helped him progress, but never having attended a racing school, he started to wonder if there were ways to improve his technique post-haste. He enrolled in a few drift courses to study the art of oversteering, and soon felt at ease asking the S2000 to rotate a little more than before.

Both his approach and the S2000’s setup are far from perfect, and Joe’s wise enough to admit that. “I haven’t thought much about adjusting the dampers — most of the time I just leave them in a neutral position and try to drive as best as I can.”

But the results from a relatively short time spent on track speak for themselves. He’s learned at a remarkable rate and, with a little more guidance from the knowledgeable group of friends he’s made recently, he’s bound to be fighting for podiums at the front of the S3 class sometime soon. He still has a few points to play with — and they’ll go towards a Zebulon rear wing, a larger Alumalite splitter, and Professional Awesome tunnels.

Joe’s studious nature has also helped him better understand the endless tradeoffs that building a track car requires. While the major cost associated with getting a rough car off the ground can eat into an aspiring driver’s budget, the peace of mind that comes from driving a flawed, imperfect car can help a driver push hard — harder than they likely would in a pristine example. That’s why he has no regrets taking the rocky but fruitful and informative path he took.

Michael’s 350Z: Take A Chance, Prove a Point

Twelve years with an unloved chassis has given Michael “Stubz” Hillo a unique perspective on taking the underdog route. There are other established, well-paved paths with minimal maintenance and certain outcomes, but they don’t offer a maverick a chance to prove a point.

Stubz took it upon himself to take the unloved 350Z and make it into a NASA ST4 race-winner because, well, he hated the idea of conforming. However, before he started his mission, he was after an affordable way to begin drifting. Nowadays, the 350Z is one of the few Japanese sports coupes that offers the sort of value the budget drifters offered back in drifting’s heyday. Even then, it was pretty cheap.

It was more than just an option for the cost-conscious drifter, as Stubz realized. Beyond low overhead, a torquey motor, and a rear-drive layout, the Z has a lot going for it. It’s reasonably stiff, the aerodynamics aren’t terrible, and the aftermarket is decently sized. It might not be as well supported as the E46 M3, but it offers similar power-to-weight figures and the potential to run respectable lap times at a fraction of the price.

The zeal and the commitment to proving the platform came later — at first, it was cheap fun. Beating up on pricier cars was only part of the pleasure; the steering was full of feel and responsive, the motor responded well to modifications, and the rear end put the power down decently.

Some of that luster began to fade when he tried to turn the Z into something more than a midfield car. The budget modifications no longer seemed to be enough, and so he tried experimenting with the high-end brands which only offered limited support for the Z.

After testing Penske and Godspeed coilovers, he settled on MCS two-ways with 18K springs up front and 9K in the rear. The car still lacks some of the compliance he’d like in slower corners, but it works well enough in the fast sections, thanks in part to Epsilon+ aero, that the compromise is acceptable.

The most irritation has stemmed from the car’s flawed braking system. Persistent knockback issues and lousy OEM ABS pushed Stubz into spending hundreds of hours diagnosing and attempting to find a package that would work.

Plenty of thrown wrenches and a thousand curse words later, he found a set of Stoptech Trophy big brakes that did a reasonable job. Because they moved the brake calipers closer to three o’clock, they mitigated some of the knockback resulting from the steering knuckle flexing. The remaining bugbear was the ABS system, which needed to be retrofitted with the Bosch Mk60 kit from Race Harness Technologies.

Though the braking system works decently these days, Stubz isn’t completely satisfied. Trailbraking has improved, but the outright braking performance hasn’t gotten much better. However, some of that has to do with the weight of the vehicle, which has been hard to lose with conventional stripping methods. “You’ve gotta get pretty creative when it comes to putting the car on a diet. I didn’t want to, but I had to buy carbon. Hatch, hood, front bumper, and headlight blanks from Spinnaker Composites have helped, but the car is still heavy.” he explains.

It’s transformed into a reasonably swift car in recent years, even with the diminishing returns from spending big bucks on primo parts. The 3,200-pound Z has an average of 257 horsepower which is pretty well administered thanks to 275-section Toyo RRs and the aforementioned aero. A broad powerband helps make the car less track-sensitive than some, and, anyways, Stubz no longer agonizes over finding the perfect setup. After several years of head scratching, he sees the Z as a dependable, safe, and sturdy car which is easy to run and satisfying to drive. Going for the gold isn’t his aim any longer — he’s happy with what the 350Z’s speed. Any car that can lap Buttonwillow W13CW in 1:54 is more than just fun — it’s seriously fast.

Striving to perfect the car sapped some of his ambition, but it’s also given him a few notable wins, wisdom, and a pragmatic approach that provides him with peace of mind. His lack of zeal might not motivate newcomers to try and beat the odds, but if they read between the lines, they should realize that there’s nothing with the Z as an entry/mid-level car. It might not carry an ambitious driver to the top of the podium, but its golden era-pricing lowers the barrier to entry. It’ll help them get involved faster — and in Stubz’s view, that’s better than sitting on the sidelines and dreaming of victory.

Max’s Spec Racer Ford: Lose The Ego

After Max Gokhman signed for his 2006 Cayman, his dealer insisted that he take the car to the track. “You won’t be able to fully appreciate it if you don’t,” he said. Max was hesitant — the thought of balling up his brand new Porsche terrified him, but, at the same time, he sensed the man knew what he was talking about.

Max continued to mull over the prospect of tracking his new toy, but his dealer was adamant — so much so he offered to pay Max’s entry fee. That was all Max needed to make a decision. The next weekend, he took the Cayman to Infineon Raceway and began a love affair that never tested his patience. No crashes, no major repairs, and a relatively straightforward relationship with his parts suppliers made his first few years in grassroots motorsports a breeze.

Soft Ascent

After becoming the 2014 PCA Autocross Class Champion and multiple podium-sitter in various Southern California time attack series, he sold the 987 and moved into a 2014 981 Cayman. This time, however, he wasn’t as eager to modify the car. He’d come to understand the practical shortcomings of a track-oriented car and felt he might get more from the ownership experience if he was to leave the car mostly stock.

It was around then that one of his track buddies enticed him into wheel-to-wheel racing. This would entail buying a race-only machine. Truth be told, he had considered it for some time, but the thought of wadding up a Porsche racing car turned his stomach. Even getting on track in one would be prohibitively expensive, so he explored the cheaper options available to him.

He could drive a Spec Miata for a reasonable price, but he wanted something a little different. “I was looking for a mid-engined, purpose-built platform, and — and this is subjective — something a little more interesting than a Miata,” he explained.

He loved the idea of running a “spec” car: something that encouraged close competition through mechanical parity. What about something with the same power of a Miata, but in a car which weighs one thousand pounds less? The tried-and-true Spec Racer Ford, a staple of grassroots motorsport for the last fifty years, caught his eye. Mid-engine, open-top, closed-wheel, and very cost-effective; there was a lot to like about this diminutive, bare-bones racer.

Barest Bones

The tube-frame chassis has a 1.6-liter engine from a Ford Focus sitting transverse behind the driver. These sealed engines produce 135 horsepower, and are fairly inexpensive to replace when they go bang — though this rarely happens. The emphasis here is on reliability, low running costs, and complete driving immersion.

When Max first tested the car at Laguna Seca, he was setting competitive times by the end of the day.

The sense of occasion is something that can’t be underestimated with an open-top car like this. Not only is the visibility fantastic, but getting your helmet buffeted by the wind makes driving at seventy feel like a hundred and twenty. The information relayed by the car is detailed and constant; it’s easy to feel a locked tire or growing understeer through the steering, which is remarkably sharp. “Feedback is crystal clear,” he adds.

Sitting in the middle of the chassis and knowing exactly where your front wheels are at all times inspires confidence to get real intimate with other racers when going three-wide into a turn - truly what wheel-to-wheel is about.

Some might suspect that a car this visceral and direct would come with sharp edges. In reality, it is predictable and communicative, and, as it has much more grip than power, it’s quite easy to find its limits. When it does slide, it’s fairly progressive — more so than the Cayman; nearly 300 horsepower would cause a few dicey situations when passing in a late-apex turn. Some of this is due to a compliant suspension setup, and some of it is due to the Hoosier slick made specifically for the SRF. Incidentally, it isn’t the most expensive tire. Low weight and low power help lengthen its lifespan, too.

The sequential transmission by Sadev, standard in third-gen SRFs, is another racecar element that Max learned to appreciate. Unlike an H-pattern, which is lovely for canyon drives but saps attention from racecraft; or a PDK, which is clinically precise yet fragile on cars that were built for the street; the SRF gearbox lets you bang out shifts while bouncing off the rev-limiter with abandon.

Perspective Shift

Max admits that, while the Spec Racer Ford is the more engaging car to drive, he doesn’t have the same sentimental attachment to it as he had to his Cayman. “I save the sweet feelings for my Porsche. This is a tool to help me grow as a racer. I compare the distinction between the two to owning a pet versus owning livestock.”

And with the reasonable running costs, packed fields, low power, and full calendars, he’s looking to become a competitive amateur racer as he gets up to speed on the Spec Racer Ford platform, with the help of his team Accel Racetek.

“Once I got competitive with this hobby, I learned that money spent on coaching would make me a lot faster than aero, suspension, or other bits of kit. To me, some of those seem most like things to flex over. With Perry and Travis of Accel Racetek, I not only know that the car will be ready for the next race no matter what tomfoolery I get up to on track, but that they’ll keep nudging me to be a better driver.”

Ultimately, the moral here is that with racing, as with any other passion, dropping your ego — such as by going from a venerable Porsche to a humble Spec Racer Ford — may prove to be the path to success, paved with smiles.

Sonoma’s Recent Repave Helps Set New Records

Speed SF’s drivers were fortunate to be the first members of the public to experience Sonoma’s new repave — the first in twenty-three years. One of Northern California’s most popular race tracks, Sonoma has been the site of NASCAR, IndyCar, and World Touring Car races over its fifty-five years.

Construction began after Christmas, with ABSL Construction of California milling out over 10,000 tons of asphalt from the track and pit lane, then grinding down the track, repairing old cracks, and laying the new asphalt.

Crack sealing in January.

Construction completed on February 23rd, two weeks before Speed SF was able to experience the new surface for ourselves.

The scenery was verdant, but the repave was far from green at Speed SF’s first full-track event of the season — enabling some of our front-runners to set new records in three of our Speed SF Challenge groups. Even those who hadn’t set new records set personal records. “The track is about three seconds faster than before,” Patrick Chio reported.

S4

In S4, Sean Win-Yepez cut 1.1 seconds off his previous best.

“There is more grip everywhere, but the gains are especially noticeable in T3/3A. There, there was so much grip that my power steering started to cut out!

One observation is that the curbs are not redone, so they now offer relatively less grip than the track itself, whereas before they were essentially about the same as the pavement. So, drivers who didn't use the curbs before will pick up more time than drivers who used them a lot.

My setup has remained pretty similar to last year, and I don’t think I benefited as much in the traction zones as some of the more powerful cars,” he added.

S3

In S3, power helped spread the distance from the previous bests a bit further. Spencer Kimball chopped the previous S3 record, set by him last May, by 2.59 seconds. In the last fifteen months, nothing about his setup has changed aside from some weight reduction. "The new paving really helps with consistency and driver confidence. Thanks to the smoother surface and lack of cracks, you can now take T1 and T2 on proper line instead of diverting your path to avoid surface undulations. I have yet to analyze my data and compare it to my previous run’s, but my lap times were about two seconds faster than my last event at Sonoma in 2023.

Based on my quick and dirty analysis, time was gained in T1, the exit of T6, and the T8/8A esses. One of the coolest features of this totally fresh paving is that my tires looked brand new after the event. Once it's rubbered in, I think we'll be seeing a lot more sub-40 cars at Sonoma,” Spencer predicted. 

S2

In S2, Maxwell Lisovsky was able just to show what his monster E36 is capable of. It has benefited from the most development as of late, but that doesn’t take anything away from his staggering 1:39.3 — a whopping 3.5 seconds faster than his previous best. Now, applying the power cleanly in second-gear corners is almost an afterthought for a sorted track tool wearing slicks.

It seems that, due to gaining something more in the traction zones, the punchier cars have been able to take better advantage of the new grip available. However, even those in the budget cars and the underpowered scalpels will find something to love about the fantastic new surface at Sonoma Raceway. These times bode well for the future, which promises novel challenges for drivers and opportunities to push harder than they ever have before..

To sign up for Sonoma event on June 21st, click here.

.

Aidan’s GT3: Vision Realized

Photo credit: @z_stills & @tengerphoto

As Aidan Vo moved through adolescence, his affinity for cars carved out a prominent place for him in the San Jose drag racing scene. After he built an all-motor DC2 Integra capable of twelve-second passes, the big magazines came calling. This was the early 2000s, when the tuning scene was enjoying its biggest boom.

Through some of his drag racing acquaintances, Aidan eventually made the leap into road racing. Following his foray at Thunderhill, he started outlining a list of changes the Integra needed to become a corner carver, and for a moment, it looked like Endless might foot the bill.

So Aidan began disassembling the Integra and shelving the parts which wouldn’t do much good around a road course. Halfway through the teardown, he had a change of heart. He parted the car out, sold the chassis to another racer, and decided to hitch himself to the all-wheel drive wagon that’d just reached American soil.

It was in a Subaru WRX STI that really learned how to turn fast laps. His confidence bolstered by the safe, accommodating four-wheel drive, he earned his spurs in relative comfort. Then he switched camps and built a cost-no-object Evo X, which earned several magazine spots. Not only had he become well known and capable around a road course, he’d been rewarded for expressing his inner vision.

As his income grew, he started searching for a new platform. Something with a little more panache — something German.

The big Audi RS4 might not have been at home on the track, but the fit and finish of a plusher, posher machine did spark his imagination. There was something distinctive about it; something which resonated with Aidan and his appreciation for high style. The jump into the Euro market got his imagination running, but, unfortunately, that would be the extent of his involvement with cars for some time.

After living through the height of the tuner craze and enjoying all that the burgeoning market could offer, Aidan stepped away from cars to focus on his career and his growing family. All throughout this quieter interim, he couldn’t successfully quiet one part of his mind. “I missed that buzz; I had to create and build again,” he reflected.

Ten years of car-free focus had done wonders for his finances. Not completely car-free, however; he spent many evenings over that decade drooling over builds his younger self could never afford. When Aidan decided to return to his old hobby, he brought with him the means to realize a plan he’d held for a decade.

“I’ve always been captivated by the Porsche 911 since the 993 generation,” he began. “It’s always had a clean, restrained, understated design — that’s a big part of my aesthetic.”

A few weeks later, he rolled his new 991.2 GT3 into his garage, parked it, and pictured the finished product in his mind with all his planned modifications. The challenge he’d set for himself was considerable, but he had a clear plan and a few connections to help him along.

The Singer DLS was the one machine which inspired the build. “I’m not a Porsche purist who doesn’t believe in tinkering on their car. I see a Porsche as a vehicle that I can use to promote my vision.”

Knowing that the name Manthey was synonymous with Porsche performance, he did what all GT3 owners with grand aspirations for their build would do: purchase Manthey’s complete suspension, brake, and aero package.

There are only a few GT3s equipped with these parts in the Bay Area, and for good reason — one kit costs as much as a newish economy car. Most struggle to justify spending nearly thirty grand on Manthey-tuned KW dampers, solid bushings, brake lines, pads, dry carbon wing, as well as a Cup car’s front splitter, but the resulting crispness and composure is worth it to those with discerning taste and deep pockets.

Perhaps the one downside was that, for all that money spent, the car didn’t look much different than it did prior to the modifications. With so many Porsches looking so similar, Aidan decided to give a nod to the Porsche styling of yore by replacing the factory GT3 wing with a Porsche Sport Design ducktail. He learned shortly after just how difficult it would be to swap out this piece, retain all functionality, all while using OEM Porsche parts — and only OEM Porsche parts.

A hundred calls to local dealerships resulted in the same sad message: “on indefinite backorder.” It took months of perusing before he found an appropriate ducktail from a local owner looking to return his Sports Design-equipped car to stock, but he finally found the part. With the ducktail in hand, he felt as if the build were gaining a momentum of all its own. “Finding that part gave me the confidence to continue doing things the way I want to do them. Everything happened so organically, it almost felt like destiny.”

It’s subtle, but it sets it apart from the rest of the winged GT3s driving around San Francisco.

Of course, the body and the engine underneath would require several tweaks to accept the new boot-lid. Aidan had to source a 911R intake, 911R engine cover, the hinges, every nut and bolts and the oil return lines to allow this new body panel fit snugly. Unfortunately, What would seem to be a simple swap took months and countless emails.

The tradeoff was obvious. “The ducktail definitely makes less downforce than the original wing, which I learned when trying to go flat over Turn 1 at Laguna Seca, but it helps with rear visibility.”

With used 911-money spent on the suspension, it would only make sense to do the same with the powertrain. With Dundon Performance on the phone, Aidan specced out an engine package that would uncork the power of the 991.2 GT3, more mid-range torque and a top-end that reminded him of some of his fastest Hondas.

Dundon provided him with an intake, throttle body, plenum, and headers. JCR provided their titanium race pipes and titanium exhaust tips. The combination of these parts together allows the car to scream like an RSR at redline while keeping a deep, sonorous growl at lower revs.

With the way the GT3 was evolving into something like a racing car, Aidan decided to try and give his car the front track and aerodynamic grip of its race-only sibling, the GT3 Cup. He rung up his contact at Manthey and ordered the primered fenders, flares, splitter, bumper, and crash bar from a bonafide 991.2 Cup car. His painter Jesus matched the new parts perfectly and even achieved OEM paint thickness.

And now Aidan has something that is undeniably his own. Even if it were for sale, his buddies would never attempt to buy it. “‘It’s so obviously his, I wouldn’t ever feel like I owned the car,’ one of my friends told me.”

But is it a show car or a track toy? Aidan doesn’t believe there needs to be any distinction between the two. He’s made steps towards having both distinguished looks and serious performance, and all that he’ll need to do to suit his mood is change a few bolts and reorient the engine fans.

“As pretty as the trunk is, it definitely lacks downforce compared to the Manthey carbon wing. I’ve planned ahead to regain the downforce we all crave at the track. I have a Cup decklid and wing ready for track days. That arduous ducktail swap was done specifically to allow swift decklid swaps when it comes time to take the GT3 back to the track. All you have to do is reorient the fans to fit the subframe brace. After that, you’re off to the track.”

At this point, he feels he’s nearly realized his vision. Aidan cannot see himself selling the car, but that doesn’t mean he’s going to make it a collection piece. Instead, he’ll put it through its paces, enjoy it as both a driving tool and a rolling piece of art, and hope that his commitment and the car’s obvious quality will inspire the next generation of speed freaks with an eye for design.

Scott’s Turbo Miata: Slippery Slope

Halfway through a warm afternoon session at Buttonwillow, Scott Smith found it getting progressively tougher to get his Nismo 350Z into gear. He pulled in and quickly found the source of the problem: a failed clutch slave cylinder, a common issue with the Z33 HR platform. Soon, it was impossible to get the car into neutral, so he stalled it, called it a day, and limped it home to San Jose.

Before Scott left, SpeedSF’s Don gave him a chance to sample a svelte sports car — something to help lift his spirits a little. Don’s 1999 Mazda Miata was fairly basic, but with a built motor, sticky tires, a roll bar, and a racing seat, it provided the sort of thrill Scott was searching for. After a couple sessions in the refreshingly direct Miata, he started wondering what he was doing with the big Nissan. “If you decide to sell it, give me a call,” he urged Don.

One year later, Don made that call and Scott made the Miata his own — and began putting his mark on it by squeezing a little more out of the motor, which was already pretty peppy by 1.8-liter standards. Scott added a Skunk2 throttle body, a Mazdaspeed Miata exhaust cam, and the JDM flat top manifold for a total of 163 wheel horsepower and 140 lb-ft of torque.

It didn’t need much more for fun laps at half the Z’s cost, but Scott decided to splurge and lay the foundation for a grand build. The top-shelf Xidas, housed in 500 and 900-pound springs front and rear, respectively, may have been a bit much for such a basic car, but they did futureproof the build. He didn’t know it at the time, but he was just beginning a long tumble down a slick hillside towards excess.

To capitalize on the bump in power, Scott installed a Mazdaspeed six-speed gearbox and an OS Giken 1.5-way differential with a 4.77 final drive. While Joe Chang was building the diff, Scott asked him to build a custom splitter and air dam to glue the front to the track. For some time, this and a rear gurney flap was enough to keep him contented, but eventually the allure of a big wing thing caught his attention and he bolted on an APR GTC 300 at the rear. Though the spring rates were borderline overkill prior to adding the aero, they made it so he didn’t have to alter the suspension to support the moderate downforce produced by the the new elements.

In Scott’s mind, the Miata was then about as fun as anything in that price range. For something that could lap Laguna in the 1:42s, it was reasonably practical, too — practical enough to drive to the track and back in relative comfort. Since his main aim was getting the most out of the basic package he’d put together, he didn’t feel the need to touch the car for some time. Instead, he focused instead on maximizing seat time, and the approach paid off quickly; he soon broke the two-minute-barrier at Buttonwillow 13CW with a 1:58 and set a SpeedSF Challenge S5 record in the process.

That no-stress, no-mess lifestyle was addictive, but, whether he wished it or not, it had to come to an end. Most people start seeking big upgrades to again experience the spark that drew them to the car in the first place. In Scott’s case, a major modification was almost forced on him after a connecting rod punctured the block and started a short but violent oil fire. That day, several onlookers witnessed a Miata-sized fireball rolling down Sonoma’s drag strip. Thankfully, George Kibilov, then driving the car, was prudent enough to wear his fire suit and emerged unscathed. The car did not fare as well.

Thankfully, aside from the perforated motor, the damage was largely cosmetic. The rear bumper was scorched as well as the underside, but not beyond repair. Scott took the opportunity to go two feet in and make what was once a mild street car into a single-purpose track toy.

The second stage started with a return to Joe Chang for a custom motor. Joe directed the build and, since Scott was planning to turbocharge the motor, he suggested 9:1 compression, Wiseco pistons, Supertech valvetrain, ACL bearings and bolts, and a “secret Joe Chang spec” head.

Before Scott decided on the right whistler, Joe directed him to Jei Chang at Blacktrax for tuning. Jei advocated for the Adaptronic ECU and a GM ethanol reader so that the engine was both reliable and adaptable enough to accept different blends.

The turbo kit came courtesy of Ed May of 949 Racing. Ed had already run the kit on his own track car, but decided he’d be better off without a blower after deciding to return to autocross. The kit consists of an Absurdflow log manifold, a Garrett GT2871R turbo, a 3” exhaust, an upgraded Walbro 255 fuel pump, 1000cc ethanol-compatible injectors, a custom oil cooler and pan baffle, and an upgraded oil pump.

On a conservative twelve pounds of boost, the motor makes 254 horsepower and 208 lb-ft of torque at the tires. Added power was only part of the appeal — the kit was completely troubleshot, and the GT2871R promised near-instant response.

Jei’s tuning helped shape a flat, broad and usable torque curve — so usable that Scott can use fourth gear exiting corners which once required he use second. Jei programmed the AIM MXL dash to warn Scott of unsafe conditions. The AIM also reports the ethanol rating and self-adjusts the boost based on said value.

The added torque doesn’t change the driving experience much, but Scott did beef up the brakes and tires after boosting the motor. A set of Wilwood Dynapros up front and Maxxis RC1s on 10” 949 Racing wheels all around helped him brake for and accelerate out of corners in much the same way he would when his motor made half the grunt.

The turbo motor has been reasonably reliable in this guise, but there’s no getting around heat issues in the middle of summer. After three turns into a hot lap at Laguna Seca, the AIM warned Scott of creeping oil and coolant temps. The brakes had a habit of getting soft, as the turbo is just inches away from the brake fluid reservoir. Ducting and vented hood louvers proved valuable at the next event, keeping temps in check. As for the brake fluid, Scott wrapped the reservoir in an ‘aerospace thermal blanket’.

With the times kept falling rapidly, Scott began thinking a little masochistically. He figured that, since his car was well past the point of streetable, he figured he may as well take the next steps in his search for additional speed and scrap any hopes of keeping the car civlized.

Then Scott stripped the car and hired Tony Colicchio to install a full Spec Miata cage. Tony knew that weight was still a primary concern with this super Miata, and thus the cage was kept as simple as the weight, power, and outright speeds required; extra bars would only slow it down.

In its current configuration, the Miata weighs just 2,250 pounds. Being that svelte is a major factor when navigating slow, technical courses quickly; Scott can lap Thunderhill West in the 1:19s without too much effort. At faster tracks, the downforce plays a much larger role; it’s what allowed him to log his best-ever lap at Laguna last weekend: a 1:36.4. Scott notes that he ran multiple 1:36s throughout the day, while still “short-shifting and babysitting the gauges” and that “this car is my Spec Miata on steroids. It’s ten seconds faster at Laguna and Sonoma, but still dances like the Spec car; it just has to be driven harder given all the extra grip!”

The car currently runs on RC1s, but with points to grow in S3, he’s decided to find more grip — both mechanical and aerodynamic. A set of 245-section Hoosiers and a revised front splitter might help him shave another few seconds off his personal bests, and if all goes to plan, he might be able to shake things up at the front of the S3 grid to keep Legend (Toyota Supra), Joe (Lexus IS-F), and Patrick (E46 M3) on their toes.

For all the additional speed, Scott has paid a price. Not just the dollar value of all the goodies, but the ‘fun’ of lugging along his Spec Miata trailer, having to monitor the gauges on sweltering days, and bringing thirty gallons of E85 each outing.

Like so many in this position, he’s found a streetable compromise very appealing in the last couple years. After trying a few fast, heavy, and focused street cars, he settled on a PDK-equipped 987.2 Cayman S and threw the most basic of footwork mods at it.

This mildly fettled street car will lap Laguna Seca in 1:38s all day and carry Scott home from the track in total comfort. Plus, with the speeds it’s capable of, Scott has plenty of potential sparring partners; he can annoy any number of M3s if he wants to. It represents the inevitable compromise that every former purist arrives at eventually.

Simply put: it just works. No muss, no fuss, no ramps, no numb legs from sitting too long in a cramped bucket seat. It’s almost relaxing compared to the little firebreather. It’s only a couple seconds off the Miata at most tracks, too.

However, lap times only tell so much about the experience at speed. The Cayman may be competent and seriously quick, but the Miata is a pure, unadulterated thing that leaves Scott smiling for the rest of the afternoon. Is that extra oomph worth the headache? Well, it depends on the week Scott’s had. Some Saturday mornings call for a triple espresso injected directly into the carotid, and others are best with a comforting cup of chamomile.

Walter’s Sentra: Lifetime Obsession

A lifelong Nissan fan and a crew member for an old NASA team running an SE-R, Walter seemed destined to pick up this particular Sentra. His family had brought him up on Zs and Maximas, so when Walter turned 16, he bought his first car, a 1991 Sentra.

That sowed the seed for the next several years. Inspired by Need for Speed, he started tuning his Sentra and soon became a knowledgeable voice in the community as well as an in-demand mechanic. His reputation opened the door to crewing positions for several big teams running in NASA’s SE-R Cup series back in the early 2000s — some of which even ran in the 25 Hours of Thunderhill.

In 2003, Walter stepped away from cars to focus on family. That break lasted for fifteen years. After that long interim, he picked up an E46 M3 and started driving himself. As good as the BMW was on the track, the love for the old Sentra, now mixed with his recent racing experiences, led him to consider building a special Sentra for racing. However, he couldn’t spare the time he once could, and so he hoped something half or wholly-built would pop up in the classifieds.

When an old friend reached out to Walter with news of a special car for sale, he felt like his stars had aligned. Not only was this particular Sentra built by MotoIQ’s Mike Kojima, but it had been the brother of a car Walter was familiar with — one which had been raced in SE-R Cup back in the day.

That particular car from his crewing days was named “Dog I.” This was “Dog II,” the sister car. The two had been given their monikers from their Petco sponsorship; they had pawprints plastered all over them during their racing days. The latter wasn’t used much in Spec SE-R, but it had seen some action in the Pacific Tuner Championship ten years ago. Since then, it’d been stored and taken out for the annual track outing. The price was right, the build quality was obvious, and the decision was easy. Walter drove his truck and trailer down to LA that weekend and began a new relationship that joined his past with his future.

Like its sibling, Dog II is built upon a body-in-white build with all the right parts. The motor, a 2.1-liter SR20VE with 11:1 compression, produces 200 horsepower and 170 lb-ft of torque on a 50-50 blend of 91 and 100 octane fuel. It’s a peaky motor, but with only 2,600 pounds to push along, it makes do.

An oversized Koyo rad is part of the beefy cooling system that helped Kojima run the car comfortably in desert heat.

Handling comes courtesy of a square set of 235/40R17 NT01s wrapping Volk TE37 wheels and an intricate cage connecting all four shock towers. Ground Control coilovers, plenty of front camber, and a bump steer kit help the car follow every minor steering input. The final touch, a little bit of rear axle bending to toe the rears out slightly, contributes to the Sentra’s immediate turn-in — the kind that is vital in a front-drive sedan. “Super oversteery” were the words Walter chose to describe its balance.

The car was just about perfect. Aside from updating the safety equipment, Walter felt it needed nothing. That was until he drove it on track for the first time and struggled with the peakiness of the motor. Despite the SR20VE’s variable valve lift, it isn’t quite as tractable as he wanted. So when picking out a new Nismo LSD, he specified a 4.75 final drive to keep the engine in its sweet spot more of the time. And like that, he was done with modifying it.

The problem with a car like this, even a relatively simple car that’s nearly completed, is that it requires a trained race shop to maintain it. He leaves it to Tarek at All Automotive in Mountain View. “They have the suspension geometry expertise and motorsports experience needed to direct the continuing development of the vehicle as well as continue the maintenance needed after every season,” Walter adds.

Now that the Sentra’s up to date and running reliably, he hopes to put in as many track days as he can. It hardly uses its brakes; the Wilwood four-pistons and 11.75” rotors are understressed. For how fast it is, it’s remarkably easy on consumables. It’s still on the same set of tires the car came with, too.

He played a supporting role for many years, but once the ball was rolling and he was able to sit himself in the seat, things have gotten steadily better. His racing education helped him make the right decision when it came to buying a purpose-built car — one which has given him the opportunity to put in his 10,000 laps without having to regularly wrench on the car. The fact that he’s finally getting to hone his driving skills on track in such relaxed fashion is sweet, but it’s not quite as sweet as being able to simultaneously revisit his tuning heyday and witness his racing future expand.

Speed SF Challenge 2023 RECAP

Speed SF’s committed clan of drivers kept the Challenge season full of excitement this year. The competition was fierce throughout most of the classes, the fields were full, and the number of new course records — nearly a dozen — proved the rapid rate of evolution, both from car and driver.

In S1 and SX, Steve Melson was our standout. His more-is-better approach to track days; running his McLaren 765LT, his Audi R8, and his Mercedes GT S simultaneously, proved he knows how to make the most of his (seat) time.

Unfortunately, his busy schedule prevented him from attending the required number of events to qualify for a podium place, but his occasional appearances were filled with laps thanks to the triple-session approach he’s made his own. Still, even with relatively few appearances this year, Steven was able to set a new S1 record at Laguna as well as a new S2 record at Thunderhill West. We look forward to seeing him next year.

Steven’s McLaren is, without a doubt, the fastest stock car currently in our ranks.

In S2, George Brooks, a newcomer to our series, established himself as a front runner from the start. His potential was clear after winning the second event, and the combination of consistency and his C7 Corvette’s acceleration kept S2000-driving Champion Gary Yeung on his toes. George's early-season pace wasn’t a fluke, either – he proved himself quick at numerous circuits with front-running positions all throughout the season. In fact, George did not miss a single event this year.

His commitment paid off; culminating in a double-points victory at the season finale at Laguna. Though George’s effort could not beat Gary’s outright pace in 2023, we have no doubt George will give Gary and the rest of the S2 contenders hell this year.

A simple Corvette and good support helped Thomas find his potential quickly.

Newcomer Thomas DiGioacchino rounded out the podium. His C5 Corvette and his driving improved considerably over the course of the season, and his five podiums stand as testament to the fact that, even with relatively little experience, putting yourself in good hands can help you hone your craft quickly.

On top of the regulars, there were four reclusive geniuses making up the ranks this year — each of their one-off wins kept everyone guessing. Seigo Ma (S2000), Steve Melson (Mercedes GT S), Kai Anderson (Camaro ZL1), and Tailai Lihe (Supra) might not’ve been in attendance every weekend, but they didn’t need to be to stand at the top of the podium.

In S3, we saw the closest title battle among any of our classes. It was Spencer Kimball and his well developed E92 M3 who eventually took the crown, but Legend Brandenburg in his modestly tuned Supra kept most of us guessing. The title wasn’t decided until the season finale — where the difference between these two was a mere eight points. Legend took the win that day, but it wasn’t enough to offset Spencer’s dominant performance from February to December.

Spencer’s M3 has had all its issues addressed and now puts in remarkable times consistently.

Tailing closely behind, mainstay Joe McGuigan in his recently sorted IS-F made the last step of the podium, and, it should be said, kept Legend and Spencer honest throughout the season. Also worth a tip of the hat was Ken Cemo, who attended every event and drove his Camaro exceptionally well. His upbeat attitude and commitment slate him as a future podium finisher.

Sean’s tidy driving made him the dominant driver in S4.

The S4 field was by far the largest, with thirty-three competitors and a close battle between S2000s at the top three steps. Sean Win-Yepez followed the wise words of Aki at Blacktrax and kept his S2000 simple and the changes minimal. Additionally, Sean started running double sessions to maximize seat time. This allowed him to run most of his best laps in the Gold Open Passing group, which reduced the pressure and made it easier to set a hot lap. With seven wins and eight new lap records at the end of the season, Sean’s holistic approach had clearly paid off.

While Sean set the S4 standard this season, it was wildman Nate Hackman in his milder S2000 sliding close behind and providing the entertainment. His flamboyant driving style was not merely exhilarating to watch, it was seriously fast; his bests often just marginally behind Sean. Maybe Nate will max out his allotted points in 2024 and give Sean an even tougher time.

David Haro snuck in a solitary win — another gold for the S2000 clan. We anticipate the other S4 contenders — Scott Smith (987 Cayman) and Patrick Chio (E46 M3), winner of the S3 season finale — nipping at Sean and Nate’s heels throughout the coming season.

Patrick (M3) added a passenger seat in order to run in S4 for the final event and showed most of the class his heels.

In S5, the two heavy hitters in the lightest cars traded positions all season. In addition to setting a slew of records at Thunderhill, Tyler Packard took his RX-8 to the title, but that was not certain until the final few rounds. S5 is anyone’s game as long as they show up frequently, as Patryck Sworonski (NA Miata) proved with an equally impressive series of wins and seconds. In the end, Tyler attended one more event than Patryck, and that made all the difference.

We hope to see both new and familiar faces ready at Laguna Seca on February 18th, where this year’s Challenge will officially begin.

On a technical note, our Competition Director Scott Smith has made a few modifications to both base and modification points to further converge on competition parity.

To view our class calculator for the 2024 season, please follow this link.

Passing Etiquette: Making Space and Saving Face

Photos (unless specified otherwise): Trevor Ryan

Overtaking is a tricky business, and learning how to pass decisively and safely takes time and practice. It pays to err on the side of caution — especially with unknown drivers. After all, squabbling for position isn’t the most judicious thing to do when there’s no prize on the line. Nobody wins a track day.

As a general rule in racing, the overtaker must present themselves alongside the driver in front — typically with the overtaking driver’s front wheels ahead of the overtaken driver’s rears before the turn-in point. This way, they’re able to see the other driver through their peripheral vision. Studying one’s surroundings and knowing where other cars are at all times is necessary to become a capable track driver.

It pays to be seen. Credit: CC-by-2.0/MIDWST.BLUR

Of course, this is a rule followed in wheel-to-wheel racing. With Speed SF, the passing car must have its front wheels in-line with the passed car’s front wheel before the beginning of the braking zone if they want to attempt a pass. It’s worth giving everyone a little more room since nobody can truly win at a track day, after all.

Our aim is to give all our drivers their own space and help the faster drivers safely navigate the slower traffic so nobody gets held up.

To give assertive advanced drivers the leeway to pass freely while allowing novices time and safety to ease their way into it, we have outlined some hard and fast rules for our various run groups. For those groups with stricter passing rules, like Green and Blue, the process of passing is made as simple as possible.

Novice Group (Green)

Responsible novices dedicate most of their mental energy to driving their own car, so they likely lack the bandwidth to watch their mirrors while driving. For this reason, we only allow passing on the designated straightaways — never through the middle of a corner — to simplify the mental burden. The courteous driver being passed should lift off the throttle to make life easier for the passing driver. This really helps when overtaking in a Miata.

When the driver being passed decides to lift off their throttle, they give the passing driver more room to complete this overtake prior to the braking zone, which is our second requirement. The passing driver should not be pressured into squeezing themselves down the inside at the turn-in point. Just because someone, especially a novice, gives the point by does not mean that a pass is possible; the passing driver must carefully judge whether it is going to work. If it’s doubtful the pass can’t work, back off — nobody wins a track day.

Keep an eye out for that point-by. Credit: OpenTrack

Generally speaking, we like the driver being passed to allow the passing driver to rejoin the conventional driving line before turning in. If they insist on turning into the corner from an inside line (ie. a line closer to the apex than the standard line), they must navigate a shorter radius and therefore reduce their entry speeds accordingly.

Because the novice’s situational awareness isn’t as great as a regular who instinctively checks their mirrors, we require the passing driver to wait for a specific gesture from the driver ahead. By leaning their left hand out the window (or right in a RHD car) and pointing at the portion of the track they’d prefer the overtaking driver to use while passing, they give a sign of recognition and avoid confusion. Wait for a clear signal, and preferably before a longish straightaway — it’s safest and easiest to pass there.

Intermediate Group (Blue)

Even with their experience, we want members of blue group to follow the same passing rules as the members of green.

HARD RULES: GREEN/BLUE

Point-by passing is required at all times. Under no circumstances is passing in the corners allowed, and passes along the straights must be completed before the braking zone.

Point-by Recommended/Mixed Group (Yellow):

After a dozen days or so, driving alongside others at a quick pace is no longer terrifying like it once was. We try to encourage these drivers to be assertive with their car placement so as to begin the two-part process of an advanced pass. Both parties must be aware of one another, and as long as there’s enough room to overtake safely, we allow passing without a hand signal. Though a point-by is still recommended to make sure everyone is aware, it isn’t required.

There are other ways to communicate reaching an arm outside the window. For instance, the driver being passed taps their rear-view mirror prior to the turn-in point (a common acknowledgement). This indicates that the driver attempting the pass is seen and will give way. The driver ahead can also offer a corner without signaling by slowing than necessary before turn-in, usually off the ideal line. If the driver behind sees the “door opening” and the driver ahead taking an odd line slowly into the corner, they will know they’ve been given a chance to pass.

When overtaking and turning in on a tighter line, remember more braking pressure (if braking is necessary) is likely required.

HARD RULES: YELLOW

The fundamental skill required to run in this group is strong situational awareness. Drivers are allowed to pass anywhere, but only at a moderate pace. Point-by passing is recommended, but not required. Exercise caution and make sure to read the driver ahead before attempting a pass.

Open Passing Group (Red + Gold):

Highly experienced drivers aren’t protected by such rules, which means they need to read the subtler signs of a driver giving way, learn how to pass decisively, and how to present themselves so as to be seen.

To run successfully in the Open Passing Group, you must know how to improvise with car placement while keeping the general level of grip in mind. Even while driving through a corner side by side, both drivers must be able to react and, hopefully, anticipate the other’s move.

Limited visibility and reduced grip make overtaking in the rain even more challenging. Remain patient and, due to the tricky conditions, avoid forcing the issue.

Of course, open passing doesn’t mean fighting for position like it would in a true race setting, but the increased level of competition typical in this run group

Assuming both parties can recognize each other’s position on track and drive in harmony, these sorts of overtakes can be done safely. They do, however, require a good deal of spatial awareness, decisiveness, car control, and forethought. For that reason, we only allow drivers with over twenty track days under their belt (or those holding a racing license) to join this group.

HARD RULES: RED/GOLD

Twenty-plus track days or racing license needed to partake. Must be experienced with open passing. No passing restrictions as long as drivers exercise good judgment.

Final Thoughts

Cooperation is the name of the game, so try to wait until a definite sign is given before attempting a pass. Make sure there’s adequate grip available to take a tighter line than the conventional line if that’s what the situation requires. The tighter the line, the more deceleration prior to the corner is required. Trailbraking helps here.

If a train of cars ahead makes life difficult for a faster driver bringing up the rear, they’re advised to pit momentarily to establish a gap. This makes life much easier and offers a better chance of achieving a personal best.

When deciding whether or not to attempt an overtake, remember that the passing car is always responsible for ensuring a safe pass. Even if the car ahead closes the door on the driver behind, it’s the latter’s fault. Leave a little space whenever possible and never squeeze somebody on a track day.

Keep eyes up at all times, scan the environment for faster and slower cars both and behind, and try not to fixate too much on rolling speed into the corner during an overtake. Instead, prioritize a strong exit. Well, the beginners should try to do this to avoid sliding off when overtaking on the inside. The experienced drivers know that, in racing, sometimes getting ahead of the driver in front is all that’s needed; an overtaken driver can’t always respond if the overtaking driver exits the corner slowly. Again, that’s racing, and this is track day driving, where the objective is to bring the car home in one piece.

Lastly, remember that there’s nothing to win here. Track days exist to help people gain experience running independently, so giving way to a faster driver when they’ve demonstrated superior speed is a mark of maturity. Yes, it might sting, particularly if they’re in a much slower car, but leave some room for humility and open the door — following a faster driver closely can be the best sort of instruction anyone can get.

Hubert's MKIV Supra: Soft Spot

Like Ken Yu, Hubert Chan first got a taste of speed on two wheels. His motorcycling antics with his cousin Wil sowed the seed, but it wasn’t until one of Wil’s dearest friends gave Hubert a taste of acceleration that made even a 600cc bike feel a little lackluster. The stoplight-to-stoplight sprints in Phil’s modified fourth-generation Supra Turbo had Hubert hooked. “It just never stopped pulling,” he said.

However, Hubert wasn’t pushed in the direction of drag racing — he had an affinity for corner carving. An E30 M3 seemed to him the coolest cornering machine in his price range, but he struggled to find the right one. Eventually, he decided another platform might be more accessible, so he gave the big Supra a chance. This was 2013, back when both these iconic cars cost half of what they do today.

The Supra had left an indelible mark on him, and though not many had taken them to the track, his knowledgeable friends signed off on the Supra as a worthwhile sports car. When Hubert found the online listing for a clean, reasonably priced, and unmodified 1994 Turbo, he bought a one-way ticket to Salt Lake City and drove it back to the Bay, dreaming of future modifications the entire way.

The Supra Turbo had proven itself as a stellar road tripper; comfortable, quiet, and still torquey enough to pass anybody quite easily. However, it was a little on the boaty side, and Hubert sought out a few ways to improve the footwork.

First came a set of Fortune Auto 500 coilovers, and the resulting agility proved that the car was more versatile than its reputation had led him to believe. The Supra’s long wheelbase didn’t feel like an encumbrance on tighter backroads, and the way it sat securely over bumps and cambers made it quite confidence-inspiring.

The foundation was there for more power, which Hubert always knew would be the most exhilarating part of tuning this new toy of his. The promise of easy horsepower encouraged him to amass a large collection of engine parts over the course of the first year. By the time he’d had it for twelve months, he was ready to move onto the second chapter and double the power output.

With the help of mechanically-inclined friend, they pulled the factory turbochargers and replaced them with a log-style cast manifold and a Precision 6266 turbocharger, then fitted Kelford 264° cams and a full 3” Tanabe Medallion Exhaust. With some meth injection and a safe tune of the AEM V2 from Lawrence Shipman, the motor made a healthy 580 horsepower on 91 octane.

With the way the Powerhouse Racing turbo kit emphasized low-end torque, it became challenging to turn that into propulsion. To address the wheelspin issues, he followed the forum recommendation to replace the factory torsen with a TRD 1.5-way differential and increase the rear tire size to 295s, which he was able to do via widening the factory rear wheels.

For the final touches to the footwork, Hubert had consulted the Supra community for an appropriate sports alignment, but upon taking it to Elite to have it aligned, Melody Cannizzaro suggested a few alterations to his provided specs. With additional toe-in at the rear, the Supra felt reassuring and stable; enough so that Hubert was comfy stepping on the throttle in second and third gear. No longer was he hindered by the big torque, which gives relatively little warning before it hits.

The Supra had established itself a capable cruiser and a competent canyon car, but Hubert was most interested in seeing what it was like in an environment where he could really stretch its legs. It wasn’t long after that his friend Janning encouraged he take the Supra to Laguna, where he met his friend Samson, another track driver who’s been instrumental in getting Hubert up to speed.

After a few spins and some big slides, Hubert began to get a sense of just how much of the power he could use in Turns 2 and 11. The power must be applied gently in the slower corners, but it will put the power down in third, assuming the car is mostly straight. “The car was definitely driving me that day, but I didn’t care. I was addicted!” he exclaimed.

Over the next few events, Hubert began addressing the handling problems only apparent after a few fast laps. It was still a little too floppy from factory; the annoying targa top would flex to the point of requiring readjustment after every session.

Hubert parked beside his friend and mentor Samson’s M3.

Titan Motorsports’ four-point rollbar, reduced the flex and the need to fiddle on the targa between outings. Still, it remained too soft to transition crisply, so Hubert installed a set of SuperPro polyurethane bushings at the critical points in the suspension, Titan anti-roll bars, and a TRD strut bar. It’s tauter than it’s ever been, but it’s still a little on the comfier side. As a car which sees more street duty than track action currently he’s content with the setup.

Its ability to cruise to and from the track in total comfort isn’t something he’s willing to forgo in the name of going faster quite yet. The power is more than adequate, the car is controllable, and the engine doesn’t show any signs of stress. Essentially, it’s barely breaking a sweat with such limited lapping.

“I’m happy with the Supra in its current state for now, but once I get a little more comfortable pushing it, I might improve the brakes and the suspension.

It’s just an easy car to live with, and I’m afraid of ruining that. Plus, it gets so much attention in the pits. Some people ask me why I risk driving such a rare car, but I think it’d be wrong to keep it in a garage. Most people think it’s only good for drag racing, but the Supra is a great performance car — it’s very much at home on the track.”

Ken's 240SX: Twenty Years in the Making

A student of motorcycles, Ken Yu spent his formative years tracking two-wheeled vehicles at Thunderhill, Laguna, and Sonoma. Eventually, he grew tired of taking spills and started looking for a four-wheeled way to get his fix. Specifically, he wanted something easily modified and cost-effective. Back in 2001, 240SXs could be found for nearly nothing — especially ones with blown motors.

A Zilvia.net posting led him to this 1989 hatch, which had been sitting for some time and needed a little love. Well, a lot of love. Aside from the blown motor, there were some serious issues contributing to the low cost of the car. “Someone left a burger in the back. There were maggots everywhere!” Still, $1,500 was a steal.

He started with a basic set of suspension upgrades. Whiteline sway bars, Megan Racing track coilovers, SPL lower arms and tension rods.

Out came the interior and in went the vinegar solutions. Then came a stock SR20, Z32 brakes, Tokico shocks, 5Zigen wheels, and Federal tires for plenty of fun in those halcyon post-college years. And this first round of modifications didn’t break the bank; many youngsters could swing these back then — no pun intended. When a full S13 front clip only cost $2,500, it was not too hard to put a quick 240SX together.

Rather than take the typical drifting route, he decided to make his 240SX corner. At 2,600 pounds with ~200 to the tires, the 240SX could graze 100 at the end of Thunderhill East’s front straight. It was nimble enough to get around many autocross courses, too.

By transplanting the motor without replacing the coolant hoses, Ken blew a pinhole leak in a coolant line at Thunderhill in the middle of July. Three of the ringlands broke, sending shrapnel into the head. He managed to limp the car all the way home to Hayward with regular coolant top-ups, but the SR was toast. He rolled it into the back of his garage with hopes to quickly replace the motor, but he didn’t bet on the next chapter of life taking him down a very different path than he’d pictured.

Ken got married, had two kids, a dog, and bought a house, so the track toy no longer took precedence. However, he kept the dream alive over the next five years by amassing a small stockpile of go-fast parts and tools.

Starting seven years ago, from ten to midnight — after the kids had gone to sleep, Ken would sift through his parts pile and make small steps towards rebuilding the car. Megan Racing coilovers with Swift springs, a pair of Sparco seats, an extensive cooling package, and a bolt-in cage set the tone: it was going to become a full-on track car built on years of forum trawling.

With his new CD009 on the floor, Ken spent a couple nights fitting Jun Flares and GarageMak overfenders.

Lots of research was needed to find out all the desired suspension settings for the 240SX — no darling of the track day community. With relatively scant information available for track-oriented S-chassis, he had to consult some of the video library he’d amassed over the years. “I’ve been watching Video Option since Volume 12.”

As this would be a fat-tired track car with a need to put power down better than what a stock S13 ever could, he had to identify the flaws of the suspension setup.

Up front, he added a set of Geomaster knuckles to lower the roll center for improved camber and toe curves. Along with that, he threw on most of the S13 parts in the SPL catalog, Techno Toy Tuning’s lower front arms, and even an S14 rear subframe for slightly better geometry and a wider track. Thankfully, retrofitting the older car with this S14 part only required a set of conversion bushings.

It would have to stop well, too. There were the two-piston rear Brembos sourced from a 2004 Subaru STI and mated to two-piece Girodisc rotors with Carbotech XP12s. Installing them was a cinch, too — almost a bolt-on affair.

At the front, the Core4 Motorsports Wilwood six-piston with Carbotech XP16s fulfilled the same need for easy modification, while offering far more reassurance than any hodgepodge of other car’s parts. Any track rat loves knowing that the kit on their car has been used by Core4 on their Silvia build for AER endurance races.

“Collecting all those parts was what kept the dream alive.”

When the ball was officially running, he called on two respected old school shops to help him rebuild the one piece he didn’t replace himself. Lonnie Jenson Co increased the SR’s bore to 86.5 mm and assembled the bottom end with Eagle rods and CP pistons. Performance Options rebuilt the head, while Ken added HKS Step 3 camshafts and dual shim rocker guides to keep the head from vibrating itself to bits at higher revs.

With a whole new fuel system and a Link G4X standalone ECU to decide on the right blend, Ken knew that he’d be stretching the stock gearbox to its limit. A Mazworx conversion kit, a CD009, and an ORC twin-clutch disk made up the the beefy new drivetrain — more than strong enough to handle 360 horsepower at 310 lb-ft at 5,500 rpm. That was sent back to an S15 helical differential with a 4.3 final drive. The combination of this gearbox and rear end resulted in explosive acceleration.

Getting tuned at Blacktrax.

After bolting in and tuning the new powertrain, the car would hook when pointed directly ahead, but the lack of compliance over surface variations caused Ken a few spins. At first, Ken struggled to find much grip coming through Turn 3 and 3A at Sonoma. “The inside wheels kept losing contact due to the lack of droop and suspension compliance. The solution was to ensure 30% of the suspension travel was reserved for droop through the helper springs,” Ken noted.

With more toe-in at the rear and a TCS Sportline rear wing, the car’s stability improved at higher speeds and under heavy braking. Being heavier in the front than the rear, it still gets a little light over the crest of Laguna’s Turn 1, but it’s less than vicious. The wingless iteration felt like it might bite his head off.

To expect much more from the projet would be unfair. December 30th was the first time he had this car on track in over a decade. And, wisely, Ken wanted to study the ways to get a dependable car out on track first.

Clearly, Ken’s done his homework. The engine manages temperatures well for a turbo car — admittedly, only cold-weather testing has been done so far, but it’s likely cooling won’t be a problem except perhaps on the warmest days.

The geometry is improved, the drivetrain handles the horsepower well, and the maintenance it requires is relatively low for an old Nissan. There’s also little tweaks that show an attention to detail and an emphasis on presentation, like how the ISR exhaust extends far enough to avoid blackening the bumper. It’s pretty — and that’s not always a great descriptor for a 240SX with bolt-on over fenders.

The attention to detail and insistence on putting reliability first will make the car’s issues easier to diagnose. However, half the car’s ancillaries are OEM SR20, so time will tell how well they’ve weathered the elements.

It’s clear Ken’s laid the right sort of foundation. Coilover testing, adding a front splitter, and increasing body rigidity are the main items on the agenda. Seam welding around the hatch and the doors — two massive apertures for such a small body — should make another massive step forward in making this middleweight handle well. Buttoning it up will take time, but Ken’s already sunk two decades into this car and his enthusiasm for tuning the 240SX hasn’t diminished one iota since the start. In the grand scheme of things, what’s another year?

Brian's BRZ: Painful Lessons in Lubrication

He’d spent years dreaming of driving on a track. Brian Armstrong had grown up hearing racing tales from his late uncle, a former professional stock car racer; and grandfather, a racer, mechanic, and performance engine builder. Even coming from good stock, Brian hadn’t really found a door into the world of motorsport himself. The opportunity finally arose when he relocated from New York City back to his native California in 2021.

Now in a more car-friendly environment, he decided to get a more track-oriented car and explore performance driving. It didn’t take long to choose a vehicle. He wanted a front-engine, rear wheel-drive platform and relatively low cost of operation. It was either the newly released BRZ/GR86 or the latest MX-5. The stars aligned when he found a 2022 BRZ in World Rally Blue in transit to a local dealer for MSRP. He put down a reservation site unseen and picked it up about a week later, in early December 2021.

In Good Company

He started with autocross, attending 4-5 events before graduating to track days. After a couple events, he found 86 Challenge, a local time attack series dedicated to the 86 platform and sponsored by SpeedSF and GT Radial. He started participating in the Stock Class, which allows only minimal modifications to the car, with the intention of setting a level playing field with a low cost of entry to be competitive. “The stock class appealed to me because all the cars are set up the same, more or less. That means your pace is primarily dictated by driver skill.”

The few modifications allowed in street class help showcase the BRZ’s brilliance out of the box; there are no drawbacks to having such a short list of legal upgrades. His car has the following modifications:

• Pedders Offset strut mounts and top camber bolts for -2.5° of front camber

• 17x8” 949 Racing 6UL wheels wrapped in 225/45R17 GT Radial Champiro SX2 tires

• AP Racing Endurance front BBK with Ferodo DS1.11 pads and Carbotech XP10 pads in the rear

• 7mm Perrin front spacers

• ARP extended studs

• GR Performance Exhaust

And he’s added a couple ergonomic tweaks: a shift knob from Ansix and, for a little added support, he inserted a section of half-inch yoga mat into the factory seat bolsters. It’s surprisingly effective!

In addition to competition, he also found community in 86 Challenge. Having faster drivers as benchmarks is helpful, but the participants also freely share information to help each other improve as drivers.“We record our telemetry data on AiM Solo 2 or RaceChrono data loggers, then share the data on Google Drive, so we can compare. It’s all voluntary, but we all want to help each other get faster.”

They were also interested in diagnosing some of the BRZ’s from-factory flaws. “We’ve also been collaborators in trying to understand and improve the reliability of the oiling system in the 2nd generation BRZ/GR86,” Brian continued. Two 86 Challenge participants had added oil pressure sensors to their cars and started documenting oil pressure drops on right hand corners as early as November 2022. After several drivers in the broader 86 community suffered engine failures on unmodified engines, including a couple who Brian knows personally, this became a bigger focus..

Brian’s analytical strengths helped him delve into the data and contribute to this effort. He instrumented his own car, with help from 86 Challenge drivers @nostreetracing86 and Miles Kodama, and published a video on YouTube explaining the issue with evidence from his car and two others. He also volunteered to test a prototype baffle from Killer B Motorsport and later Verus Engineering in hopes of finding a simple way to mitigate oil starvation.

Ironically, his engine blew the day one in-depth article he’d contributed to was published.

That expensive afternoon at Thunderhill East went smoothly until it didn’t. Initially, when Brian saw a pressure drop to 0 PSI, he first thought a sensor had failed. When he heard that terrible telltale shuddering sound emanating from his engine bay — the one he’d heard so many times in the big-hit failure videos on YouTube — he knew it was catastrophic.

Thankfully, fellow 86 Challenge driver Kevin Schweigert offered Brian space in his garage to suss out the cause of his FA24’s failure. With the pan on Kevin’s garage floor, Brian took a peek. It took two seconds to determine what had happened.

A small piece of metal had broken off the baffle and blocked the oil pickup. “It was a one-of-one prototype build, so these types of things can happen. Verus immediately accepted responsibility and said they would help with the rebuild.” They covered the cost of a new FA24 long block and, through generous donations from the community, Brian was able to cover the cost of labor and additional parts needed for the rebuild.

Second Stab

During this rebuild, Brian took advantage of the opportunity to make some improvements to his oiling system to try and increase durability and decrease flow restrictions, which can decrease pressure to the crankshaft.

His old oil cooler lines had been rubbing on a sheetmetal seam near the driver’s side headlight and there was insufficient protection from abrasion. It could have been a serious issue if not addressed.

Following advice from other 86 Challenge members, he decided to replace the lines with custom built Goodridge 910 AN hoses—as used in the GR86 Cup Car. These kevlar-braided lines are more abrasion resistant, but also feature a larger internal diameter, for less flow restriction. He also increased the size of the oil cooler core with the hope of reducing temps and reducing flow restriction.

His shakedown of the new engine, oil cooler, and a new generation of oil pressure instrumentation hardware at a recent SpeedSF event was auspicious. Everything worked well, Brian was at ease, so he pushed a little harder than normal set a new PB.

Brian’s committed to the cause. His continuing work with Verus aims to solve this starvation issue and the pair is planning to test a new prototype in January. They now believe the primary issue may be related to the oil returning too slowly from the heads to the oil pan, which the prototype attempts to fix.

The community support and innovation from the major aftermarket players have encouraged Brian to continue chancing his baby in an attempt to solve the problem which worries most BRZ owners. Undaunted by the big bang this year, he’s planning on returning to Stock class in the 86 Challenge in 2024. Consider it a testament to a lovely atmosphere among cooperative drivers and an exhilarating platform worth taking a few risks for.

You can follow him at @900BRZ on Instagram and YouTube.

Thomas' Corvette: In Good Company

Finishing out his senior year of high school, Thomas DiGioacchino listened to a friend’s suggestion and scrounged the money together for his first track day. Crap tires, decent weather, and a near-stock Mustang GT were all he needed to find that thing that’s been steering his life for the last five years.

Thomas decided to pursue the mechanical side of things and enrolled in Ranken Technical College’s High Performance Technology course with a focus on Chevrolet LS engine design.

That emphasis allowed Thomas to build a motor for a car he hadn’t yet bought. It began with an iron-block LQ motor and LS1 heads, and as the LQ block only displaced 5.3 liters, he bored and honed it out to 5.7 liters to fit the LS1 head. With forged pistons and rods, oil pan baffles, and the other pieces that made it a 500-horsepower workhorse, he unknowingly set the tone for the rest of this build.

The car itself came next. During his final year at Ranken, he found himself a base 2002 Corvette within his price range and tucked it away in his side yard until graduation, when he loaded up his truck with his furniture, his motor, and began his drive from Missouri to his hometown.

Back in San Mateo, he reached out to his then-limited network for car parts and, with some luck, gainful employment as well. As he’d relied on Elite Performance to direct him towards a few bolt-ons for his Mustang, they were the natural resource to consult. One day, while speaking to Elite’s Melody Cannizzaro about getting his Corvette aligned, she provided up with a job opportunity. He didn’t have to think twice.

Working with Elite gave him access to one longtime customer who happened to be offloading some go-fast bits from their recent Corvette build. Thomas was able to grab a set of Titan 7 T-S5 wheels for peanuts, and then came big brakes, bushings, and a bucket seat. Soon, the plans for keeping the Corvette tame and civilized went out the window.

Wisely, he went for safety equipment next, and decided that this car would only help him become a truly quick driver if it was reliable first and fast second. “I knew that seat time would be the priority if I was going to run with guys like Gary Yeung,” he said.

That said, it would be silly not to make use of the big motor sitting in his parent’s backyard. Soon, it found a new home in the Corvette’s engine bay, and Thomas took the half-built C5 to its first track day, where it ran without a hiccup. It ran well the second day, too, as well as the third. Clearly, he’d paid attention in class.

Aside from the minor repairs any twenty-year-old car needs, it was the epitome of dependable. His focus was on learning to drive the car better, but, to his credit, a C5 on stock suspension does leave a lot to be desired. It would lean excessively, and under trail braking, it had a habit of snap-oversteering.

After several months of saving, Thomas bought a used set of JRZ two-ways. While he was at it, he pulled and refreshed the entire drivetrain, then upgraded the springs and clutch packs in the OE LSD. Those modifications made the Corvette much more progressive at the limit, regardless of whatever cheap tires he happened to be running.

When he found the time to fine-tune the suspension, he increased the rake to increase rotation at corner entry. A square 295-35/18 setup was the cost-conscious tire option, and he stretched every set until the cords showed. Still, the car was mostly neutral with a hint of understeer in the faster stuff thanks in part to his APR GTC-300 wing.

As his confidence grew, he started to recognize that driving around on worn rubber was no longer the training tool it had been, so he sprung for a set of AR-1s and turned his first sub-two-minute lap at Buttonwillow 13CW. “I had to fight it the whole way around, but I got 1:58. A sloppy 1:58, but still,” he said.

Good tires helped, as did having a hare to chase. With Gary Wong driving his S2000 off into the distance, Thomas was able to see where he could push harder than he believed was possible. It’s a huge help having an experienced driver luring your outside your comfort zone.

Logging that first milestone lap gave him the confidence to try the Speed SF Challenge the next weekend at Thunderhill’s five-mile configuration. He did his homework and studied several record laps, focusing on curb usage. With Gary Yeung giving him some basic feedback the day of, Thomas saw his lap times fall by as much as four seconds. In the end, he was able to clinch third place in S2 — just half a second behind Kevin Schweigert in his BMW M2.

That success turned Thomas into a sponge. His subsequent lapping days have been spent studying data and having the experienced drivers like Joe McGuigan critiquing his onboard videos. “Joe’s been a huge help; giving me pointers on which gears to use so I can put the power down more easily.” The result of this traction-conscious approach to driving is evident in the footage below:

He’s also benefited from picking a short list of prime parts. In fact, he’s never bent his Titan 7 wheels or broken any suspension parts, despite hammering curbs and dropping wheels regularly. Maybe it has something to do with emphasizing robustness with this build—a tip he picked up from his mentor, Gary Yeung.

‘I’ve learned a decade’s worth of motorsports knowledge in the last two years. Everyone’s been so supportive, and I owe my progress to all of them. They’ve pushed me to improve as a driver and a builder—especially Gary. Watching him work inspired me to raise my game, and I think it shows. My Corvette’s overbuilt, so I can push it all day. Like Mango, my Corvette is a workhorse that’s made it possible to attend almost every Speed SF event in the last two years. All I do now is change the fluids and try to find out where I can go faster.”

Parts

• JRZ motorsport coilover conversion

• Titan 7 T-S5 wheels 18x10.5”

• Trackspec hood vents

• Dewitts radiator

• Spal fans

• Improved Racing oil cooler

• Improved Racing oil pan baffles

• Prothane polyurethane bushings

• APR GTC-300 wing

• APR splitter

Fenton's Integra Type S: A Change of Heart

“I used to be the biggest hater of FWDs,” he started. Despite his introduction to cars coming in the form of a Civic, he rapidly transitioned into rear-drive platforms when he took up track driving. After a pair of S2000s, he moved onto Porsche Caymans, 911s, and, most recently, a Subaru BRZ. What they all had in common was their rear-drive layout, which cemented in Fenton the belief that all other drivetrain configurations were beneath consideration.

Lately, he’s had a change of heart.

It was an unexpected decision to sell his BRZ. Oil starvation issues concerned him, but he had also owned the car for eighteen months and was starting to wonder what decent replacement was out there—something new, fun, and practical between fifty and sixty grand.

Actually, he was a little more particular than that:

1) It had to be track-capable.

2) It had to have been endorsed by Throttle House, savagegeese, or TheTopher.

3) It had to be at least as practical as the BRZ.

4) It couldn’t break the bank in the event of an incident.

Not much in that price range met his requests, but the faster Hondas, despite driving the wrong axle, were fairly close. But it was more than the drivetrain that deterred him at first.

“I remember when the base Integra was first announced, I thought Acura was disrespecting the Integra name. It looked like a boat; it had no resemblance to the DC2 or the DC5 and, I believed, was probably an overpriced Civic.”

A few months later, the Integra Type S was announced, and Fenton found himself torn. “I started to love the way it looked. Even though the general shape was the same, they tweaked the right areas to make it look like a driver’s car. This had proper flares, an aggressive rear diffuser, a vented hood, gaping intakes—it was unique and purposeful.”

“The Integra wasn’t really on my radar until, one day, I was bored at work and decided to configure a car on the Acura website. I specced out my ideal Type S, and figured I’d add my email to their list—why not?

The next day, Acura of Pleasanton, just seven miles from my house, contacted me and offered that exact car at MSRP plus $1,000 of non-negotiable dealer add-ons. One prospective buyer had backed out and my name came up on their list.”

At the time, he’d been considering the FL5 Civic Type R, though the markup was significant. Plus, the car has a number of creature comforts and tuning differences over the Civic that makes it a better daily. An Integra-specific re-tune of the K20C1 engine, shared between the two, provides much more mid-range torque. Additionally, the Integra’s electronic dampers benefit from new tuning to make it a more supple road car.

The case in favor of FWD was growing, but he still had his bias to overcome. “I used to believe that, if you cannot powerslide it out of a corner, it’s not a sports car.

However, he couldn’t find anything else under $60,000 that is spacious, has a backseat, has a manual transmission, is track-capable, and is rear-wheel drive. I realized that, in order to hit my price point, I’d have to make one or two concessions.

I figured I’d at least give the Integra a try. In person, it looked fantastic, and it felt like a $50,000 car inside. It was something I could live with on a daily basis. The shifter is nearly as good as a Honda S2000’s, the ride quality is phenomenal; with the dampers in comfort mode, it rides almost as well as a luxury car. It has minimal torque steer and phenomenal brakes. After driving it around the block, I was sold.”

He bought it that day.

Since then, he’s beaten nearly all of his previous bests. At Laguna Seca, Thunderhill East, and Thunderhill West, he’s beaten his bests in the BRZ by 2 to 3 seconds. Some of that has to be down to Integra having twice the torque, but, as Fenton’s learned, a FWD car might be easier to come to terms with.

“I can lean on the car more confidently, whereas the BRZ would break away more abruptly. I know that, on turn-in, it’s going to understeer, and while that might sound boring, it means I can get up to speed a little bit faster, especially on cold mornings.”

At Laguna Seca, he drove the tires off his car—literally. Underinflating the PS4S tires to try and keep them in their ideal range seemed sensible, but during turn-in to Turn 6, the front-right tire debeaded. “I only stopped a few feet from the wall. It taught me not to track 30-profile tires with soft sidewalls any longer.”

If there was one issue beyond that, it was the lack of support from the stock seats. “The OEM seats are inadequate for track driving; they are the same design as the base Integra with very little bolstering. The OEM FL5 seats are supportive and soft enough for daily driving and track duty. I’d happily exchange the Integra seats’ heating and electronic adjustability for the FL5’s greater versatility.”

And so he started adding the first round of modifications, beginning with a set of 18 x 9.5” + 45 Apex VS-5RS wheels wrapped in Kumho 265-35 V730s (the same as he had on his BRZ for fair comparison), as well as a set of Ohlins Road & Track coilovers.

The Road & Tracks have a reputation for being more road than track, but the Integra-spec 6kg front and 10kg rear springs are much stiffer than what’s normally offered. “The spring rates have helped a lot with tucking the nose. You can get consistent mid-corner rotation with a lift-off the throttle.”

Along with those mods, he added some Castrol SRF fluid and a set of Endless ME20 pads from RHD Japan since the yen is weak now. Their torque rating is much higher than the standard pads, which were at least resilient enough to run sessions at Laguna without fade.

With the first round of modifications in place, he took it to Thunderhill West and ran a 1:24 in his second session—some 2.5 seconds faster than he ever went in his hardcore S2000 on Federal tires. “It felt adjustable; it wasn’t a battle against understeer in every corner. You can transfer weight with the inputs and rotate the car in small, measurable increments. That’s something I find a modern GTI just won’t do.”

Most recently, Fenton ran Thunderhill East Bypass for a day that he found encouraging, if not a little frustrating. After spinning in the first session and getting the black flag, he found himself without traffic in the second session and logged a 2:01. “I believed I could find another one to two seconds in the third session, but one of the flaws of the car held me back.”

In order to completely avoid fuel starvation, the tank needs to remain above half-full. After dipping below the middle hash five minutes into his third session, he spent the remainder dealing with fuel cut. He couldn’t leave too miffed; he’d only had one real session to push the car, and with that 2:01 indicated on his Garmin, he’d already gone three seconds faster than he ever had in the BRZ.

Considering he’s only done three modifications and is already three seconds faster than the BRZ, he has no regrets. “I might not be powersliding it everywhere, but it’s taught me that there are other, subtler ways of manipulation.”

Beyond all this, I can drive to and from the track in complete comfort. With radar cruise control, lane-keep assist, blind spot monitoring, heated seats, a premium ELS sound system, and even a sunglasses holder—I’ve never been so comfortable on my way to and from the track before. Going from a partially gutted S2000, to my mostly-practical BRZ, to this, I’ve experienced three distinct improvements in comfort. Plus, I can ferry people around. There is plenty of space for four adults—roughly the interior space of an Accord from fifteen years ago.”

It’s still a little too quiet to hear with his helmet on, so he’s planning on upgrading to a modest exhaust that should make it easier to gauge where he is in the rev range, reduce backpressure, and find a little more grunt. That said, it’s not lacking in that department; it has more than enough torque to run third gear through most of Thunderhill West. Oh—it could use more front camber.

In Fenton’s eyes, it deserves to be seen as Acura’s flagship sports sedan—it’s a deserving successor to the DC2 Integra Type R. “It’s a compromised car at the end of the day, and yet they have kept all those compromises from adversely affecting driving enjoyment. To me, it’s the perfect compromise.”